Instruction/ maintenance manual of the product H5E-DV PC Bunn
Go to page of 10
BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o obtain the Illustrated P ar ts Catalog, visit the Bunn-O-Matic website, at www .bunn.com. This is absolutely FREE, and the quick est wa y to obtain the catalog.
2 INTRODUCTION This equipment heats and dispenses water on demand for beverages and cooking purposes. It has a panel above the dispense valve that indicates the status of the dispenser . This equipment is for indoor use, either wall-mounted or on a sturdy counter or shelf.
3 ! W ARNING V er y Hot W ater Use With Care!.
4 ELECTRICAL REQUIREMENTS WARNING - The dispenser must be disconnected from the power sour ce until specifi ed in Initial Set-Up. Refer to Data Plate on the Brewer , and local/national electrical codes to determine circuit requirements. Electrical Hook-Up CAUTION – Improper electrical installation will damage electronic com- ponents.
5 PLUMBING REQUIREMENTS This dispenser must be connected to a COLD WA TER system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1 ⁄ 2 " or larger supply line. A shut-off valve should be installed in the line before the dis- penser .
6 INITIAL SET -UP CAUTION - The dispenser must be disconnected from the power sour ce throughout the initial set-up, except when specifi ed in the instructions.
7 OPERA TING CONTROLS (a) VOLUME SELECTOR BUTTONS Press and release the button corresponding to the Small, Medium, or Large volume, to select the desired amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change the volume in progress.
8 PROGRAMMING When power is applied to the dispenser , the display located on the bottom of the main cir cuit board will show the revision level of the software for 5 seconds, and then go to (-). While the tank is fi lling, the display will read (FIL).
9 3. Press and release the center button once more. The display will read H2 , then show either FA H (Degrees in Fahrenheit) or Cen (Degrees in Centigrade). 4. Use the (+) and (-) buttons to alternate between FA H and CEn . 5. Press and release the center button once more.
10 WIRING DIAGRAMS J7-4 J7-1 L1 J2-10 MAIN CONTROL BOARD J2-1 J2-5 N.O. COM J4-1 J6-1 J1-11 J1-5 J1-1 PINK-22 J5-1 J5-3 GRN-18 BLK WHI J3-5 J3-8 J3-1 WHT -14 WHT -18 WHT -18 WHT -18 1800 W T ANK HEA T.
An important point after buying a device Bunn H5E-DV PC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn H5E-DV PC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn H5E-DV PC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn H5E-DV PC you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn H5E-DV PC will certainly help you make a decision on the purchase.
If you already are a holder of Bunn H5E-DV PC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn H5E-DV PC.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn H5E-DV PC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn H5E-DV PC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
