Instruction/ maintenance manual of the product FMDA DBC-3 Bunn
Go to page of 10
FMD DBC-3 FMDA DBC-3 SN FMD0013000-UP INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-664.
2 29215 080112 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor .
3 00831.0000 29216.0000 29215 051111 28368.0004 CONTROL THERMOST A T ADJUSTMENT APPROXIMA TE THERMOST A T TEMPERA TURE SETTINGS 200 F 190 F 180 F 28368.0004A 08/08 © 2008 BUNN-O-MA TIC CORPORATION OFF OFF OFF HI HI HI BUNN BUNN BUNN W ARNING ! Fill water tank before turning - on - thermostat or connecting appliance to power source.
4 INITIAL SET -UP 1. Locate the drip tray assembly above the dispenser nested in the packing material. 2. Remove the drip tray and the drip tray cover and set them aside.
5 PLUMBING REQUIREMENTS This dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1/2˝ or larger supply line.
6 LIQUID LEVEL CONTROL The system automatically maintains the hot water tank’ s level by energizing the refill solenoid when the water level drops below the liquid level probe. If the system has not successfully refilled in 15 minutes, a refill error occurs.
7 HOPPER DISPENSE RA TE OF PRODUCT The hopper dispense rates are preset at the factory . With 22 tooth gear and auger wire, the preset dispense rate is approximately 3 to 5 grams per second. With 30 tooth gear and auger wire, the preset dispense rate is approximately 5 to 7 grams per second.
8 5. Running Hopper Throw T est: The hopper throw can be checked by automatically running the hopper motor as follows: a. Remove the steam collector and mixing chamber from under the hopper to be checked. b. Position a small cup under the hopper outlet.
9 RE-INITIALIZE TO F ACTORY DEF AUL TS This resets all dispense time settings and hopper throw rates to the factory defaults, and resets the password to 0 (no password.) 1. Disconnect the dispenser from the power source. 2. Place the Rinse/Run switch in the “Run” position.
10 CLEANING The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur - faces on Bunn-O-Matic equipment.
An important point after buying a device Bunn FMDA DBC-3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn FMDA DBC-3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn FMDA DBC-3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn FMDA DBC-3 you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn FMDA DBC-3 will certainly help you make a decision on the purchase.
If you already are a holder of Bunn FMDA DBC-3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn FMDA DBC-3.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn FMDA DBC-3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn FMDA DBC-3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
