Instruction/ maintenance manual of the product DV PC Bunn
Go to page of 9
INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www .
2 39338.1 051910 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specifi ed below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years.
3 CONTENTS Warranty .......................................................2 Introduction ..................................................3 User Notices .................................................3 Electrical Requirements .....................
4 ELECTRICAL REQUIREMENTS WARNING - The dispenser must be disconnected from the power sour ce until specifi ed in Initial Set-Up. Refer to Data Plate on the Brewer , and local/national electrical codes to determine circuit requirements.
5 INITIAL SET -UP CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specifi ed in the instructions. 1. Connect dispenser to the power source and turn on water supply . 2. Place master ON/OFF switch in the ON position (if equipped).
6 PROGRAMMING When power is applied to the dispenser , the display located on the bottom of the main circuit board will show the software version for 5 seconds, and then it will show the model number (see chart below) it will then go to (-). While the tank is fi lling, the display will read (FIL).
7 39338.1 072409 LEVEL 2 PROGRAMMING H1 - DISPENSE TEMPERA TURE LOCKOUT - PORTION CONTROL ONL Y (WILL NOT DISPLA Y ON OTHER MODELS) 1. T o enter Level 2 Programming, press and hold the center button until H1 ap- pears on the display (approximately 6 seconds) then release button.
8 OPERA TING CONTROLS - POR TION CONTROL ONL Y (a) VOLUME SELECTOR BUTTONS Press and release the button corre- sponding to the Small, Medium, or Large volume, to select the desired amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change the volume in progress.
9 DRAINING THE DISPENSER CAUTION - The dispenser must be disconnected from the power source throughout these steps. 1. Disconnect the dispenser from the power source. 2. Shut-off and disconnect the incoming water supply and allow dispenser to cool. 3.
An important point after buying a device Bunn DV PC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn DV PC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn DV PC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn DV PC you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn DV PC will certainly help you make a decision on the purchase.
If you already are a holder of Bunn DV PC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn DV PC.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn DV PC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn DV PC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
