Instruction/ maintenance manual of the product DUAL068000 Bunn
Go to page of 10
DUAL ® TF DBC ® WITH SMAR T FUNNEL ® S/N DUAL068000 & UP INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE: (217) 52.
Page 2 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor .
Page 3 00656.0001 00831.0000 00658.0000 USER NOTICES The notices on this brewer should be kept in good condition. Replace unreadable or damaged labels.
Page 4 ELECTRICAL REQUIREMENTS (Models with power cord) WARNING - The brewer must be disconnected from the power sour ce until specified in Initial Set-Up. Refer to Data Plate on the Brewer , and local/national electrical codes to determine circuit requirements.
Page 5 120/208 and 120/240 volt ac single phase, 60 Hz models Note: This electrical service consists of 3 current carrying conductors (Neutral, L1 and L2) and a separate conductor for earth ground.
Page 6 PLUMBING REQUIREMENTS This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1 ⁄ 2 " or larger supply line. A shut-off valve should be installed in the line before the brewer .
Page 7 b b c c d d e f g OPERA TING CONTROLS OPERA TING CONTROLS (a) MAIN ON/OFF SWITCH This switch, located under the brewer behind the front leg, turns power on and off to all components in the brewer . (b) BA TCH SELECTOR SWITCHES Pressing the switch corresponding to the Small, Medium, or Large batch selects the amount of coffee to be brewed.
Page 8 INITIAL SETUP CAUTION – The brewer must be disconnected from the power sour ce throughout the initial setup, except when specified in the instructions. 1. Insert an empty funnel into the funnel rails of one of the brew stations. 2. Place an empty server under the funnel.
Page 9 SET READY - Range: 185˚F (85˚C) to 203˚F (95˚C) This function allows the operator to set the minimum temperature allowable to start a brew cycle. The range can be from 185˚F (85˚C) to within 2˚F (-1.7°C) of the SET TEMP . The water must be at the SET READY tempera- ture or higher for the display to indicate READY TO BREW .
Page 10 CLEANING 1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device. 2. Check and clean each sprayhead. The sprayhead holes must always remain open.
An important point after buying a device Bunn DUAL068000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn DUAL068000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn DUAL068000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn DUAL068000 you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn DUAL068000 will certainly help you make a decision on the purchase.
If you already are a holder of Bunn DUAL068000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn DUAL068000.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn DUAL068000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn DUAL068000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
