Instruction/ maintenance manual of the product A10A Automatic Bunn
Go to page of 6
POST␣ OFFICE␣ BOX␣ 3227 SPRINGFIELD,␣ ILLINOIS␣ 62708-3227 TELEPHONE:␣ (217) 529-6601␣ ␣ FAX:␣ (217) 529-6644 10613.0000C 2/94 ©␣ ␣ 1993␣ ␣ BUNN-O-MATIC CORPORATION. B UNN-O-MA TIC CORPORA TION A10 A utomatic & A10A A utomatic Supplement to A10 Use & Care Booklet #10070.
USER NO TICES The notices on this brewer should be kept in good condition. Replace unreadable or damaged labels. #00831.0000 #00656.0000 #00658.0000 Fill water tank before turning -on thermostat or connecting appliance to power source. Do not use near combustibles.
ELECTRICAL REQUIREMENTS CAUTION - Do not plug-in the brewer until specified in Initial Set-Up. The A10 Automatic Brewer has an attached cordset and requires 2-wire grounded service rated 120 volts ac, 10 amp, single phase, 60 Hz.
INITIAL SET -UP (CONT .) 8. If not, locate the brew timer near the heater switch on the left side of the brewer, adjust the brew timer dial up-or-down as required and allow the water to reheat. Start, and measure another brew cycle. 9. Repeat step 8 until 48oz water volume is achieved.
REPLA CEMENT P ARTS 04060.0000 ........... BASE EXTRUSION 04040.0004 ........... BREW FUNNEL, BLACK 04069.0003 ........... CONTROL THERMOSTAT ASSY. 01716.0000 ........... CORD, POWER 250V 10 AMP, IEC320 (A10A) 01637.0000 ........... CORDSET, 16/3HSJO NEMA 5-15P (A10) 04123.
10627.0001A 5/92 © 1992 BUNN-O-MATIC CORPORATION ORA BLK L2 L1 BLK WHI WHI/GRN SOL BLK GRN/YEL SCHEMATIC WIRING DIAGRAM A10 A AUTO "KEEP WARM" HEATER WHI LOWER WARMER 80W RED RED BLK RED 1 BREW TIMER 3 2 4 5 RED YEL SW3 230 VOLTS AC 2 WIRE SINGLE PHASE LIMIT THERMOSTAT RED SW.
An important point after buying a device Bunn A10A Automatic (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn A10A Automatic yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn A10A Automatic - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn A10A Automatic you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn A10A Automatic will certainly help you make a decision on the purchase.
If you already are a holder of Bunn A10A Automatic, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn A10A Automatic.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn A10A Automatic. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn A10A Automatic along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
