Instruction/ maintenance manual of the product 40119.0000G Bunn
Go to page of 9
TIT AN DUAL™ INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 40119.
Page 2 INTRODUCTION This equipment will brew coffee into an awaiting server or airpot. The brewer may have an auxillar y hot water faucet. It is only for indoor use on a sturdy and level counter or shelf. Please install in an area where there are no water jet devices.
Page 3 40119 010412 #00656.0001 As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes.
Page 4 40119 080108 ELECTRICAL REQUIREMENTS WARNING - If the power cord is ever damaged, it must be replaced by the manufacturer or its service agent with a special cord available from the manufacturer or its service agent in order to avoid a hazard.
Page 5 40119 010412 PLUMBING REQUIREMENTS This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) with a minimum of 4.0 gpm from a 1⁄2" or larger supply line. A shut-off valve should be installed in the line before the brewer .
Page 6 40119 080108 A. MAIN ON/OFF SWITCH This switch, located under the brewer in front of the right rear leg, turns power on and off to all components in the brewer . B. ON/OFF SWITCH (ENABLE BREW) Pressing the "ON/OFF" switch will alternately turn the selected brewing side on and off.
Page 7 INITIAL SET -UP CAUTION – The brewer must be disconnected from the power source throughout the initial setup, except when specified in the instructions. 1. Insert an empty funnel into the funnel rails of one of the brew stations. 2. Place an empty server under the funnel.
Page 8 COFFEE BREWING 1. Begin each brew cycle with a clean empty brew funnel. 2. Insert a BUNN filter into the funnel. NOTE: The funnels are equipped with 4 wire loops that can be folded over top edge of filter if desired, to prevent filter from folding in during the brew cycle.
Page 9 40119 010412 CLEANING 1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device. 2. Check and clean each sprayhead.
An important point after buying a device Bunn 40119.0000G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn 40119.0000G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn 40119.0000G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn 40119.0000G you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn 40119.0000G will certainly help you make a decision on the purchase.
If you already are a holder of Bunn 40119.0000G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn 40119.0000G.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn 40119.0000G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn 40119.0000G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
