Instruction/ maintenance manual of the product 34025.0004A Bunn
Go to page of 9
INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www .
Page 2 INTRODUCTION This brewer incorporates a wireless interface system that allows the DBC Grinder to load certain information into the "programming chip" located inside the handle of the funnel. This information includes the name of the coffee ground and what batch size will be brewed (small, medium, or large).
Page 3 00656.0001 00658.0000 20201.5600 USER NOTICES The notices on this brewer should be kept in good condition. Replace unreadable or damaged labels.
Page 4 ELECTRICAL HOOK-UP (Models without power cord) CAUTION – Improper electrical installation will damage electronic components. Damage caused by incorrect electrical connections is not covered by warranty . 1. An electrician must provide electrical service as specified in conformance with all local, state and federal electrical codes.
Page 5 CE REQUIREMENTS • This appliance must be installed in locations where it can be overseen by trained personnel. • For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C. • Appliance shall not be tilted more than 10° for safe operation.
Page 6 OPERA TING CONTROLS OPERA TING CONTROLS (a) MAIN ON/OFF SWITCH This switch, located under the brewer behind the right front leg, turns power on and off to all components in the brewer . (b) BA TCH SELECTOR SWITCHES Pressing the switch corresponding to the Small, Medium, or Large batch selects the amount of coffee to be brewed.
Page 7 INITIAL SETUP CAUTION: The brewer must be disconnected from the power sour ce throughout the initial setup, except when specified in the instructions. 1. Insert an empty funnel into the funnel rails of the brew station. 2. Place an empty server under the funnel.
Page 8 SET READY - Range: 185˚F (85˚C) to 203˚F (95˚C) This function allows the operator to set the minimum temperature allowable to start a brew cycle. The range can be from 185˚F (85˚C) to within 2˚F (-1.7°C) of the SET TEMP . The water must be at the SET READY tempera- ture or higher for the display to indicate READY TO BREW .
Page 9 CLEANING 1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. 2. Check and clean the sprayhead. Use the pointed end of sprayhead cleaning tool (#38227.0000) to remove any mineral deposits from the sprayhead holes.
An important point after buying a device Bunn 34025.0004A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn 34025.0004A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn 34025.0004A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn 34025.0004A you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn 34025.0004A will certainly help you make a decision on the purchase.
If you already are a holder of Bunn 34025.0004A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn 34025.0004A.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn 34025.0004A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn 34025.0004A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
