Instruction/ maintenance manual of the product 10267 Bunn
Go to page of 14
INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www .
2 46819 030912 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor .
3 CONTENTS 46819 043012 INTRODUCTION This equipment heats and dispenses water on demand for beverages and cooking purposes. It has a panel above the faucet that indicates the status of the dispenser . This equipment is for indoor use, either wall-mounted (H5E/X/PC) or on a sturdy counter or shelf.
4 USER NOTICES The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels. 00656.0001 As directed in the International Plumbing Code of the International Code.
5 ELECTRICAL REQUIREMENTS WARNING - The dispenser must be disconnected from the power sour ce until specified in Initial Set-Up. Refer to Data Plate on the Brewer , and local/national electrical codes to determine circuit requirements.
6 INITIAL SET -UP - H5E, H5X, H5-PC, H10X, Element CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Connect dispenser to the power source and turn on water supply .
INITIAL SET -UP - H5M CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Remove the upper rear panel and rotate the control thermostat knob fully coun- terclockwise to the “OFF” position and replace the panel.
OPERA TING CONTROLS - PORTION CONTROL ONL Y (a) VOLUME SELECTOR BUTTONS Press and release the button corre- sponding to the Small, Medium, or Large volume, to select the desired amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change the volume in progress.
9 PROGRAMMING - H5-E, H5-PC, H5X, H10X When power is applied to the dispenser , the display located on the bottom of the main circuit board will show the software version for 5 seconds, and then it will show the model number (see chart below) it will then go to (-).
10 PROGRAMMING - H5-E, H5-PC, H5X, H10X Continued LEVEL 2 PROGRAMMING H1 - DISPENSE TEMPERA TURE LOCKOUT - PORTION CONTROL ONL Y (WILL NOT DISPLA Y ON OTHER MODELS) 1. T o enter Level 2 Programming, press and hold the center button until H1 ap- pears on the display (approximately 6 seconds) then release button.
Program lockout switch: The switch must be in the “SET” position in order to access the program modes. 1. Disconnect the dispenser from the power source. 2. Remove the 4-40 screws and the top cover . 3. Use a small screwdriver to move switch to set position.
12 2. The display will now show the model number . (H5H) 5 Gallon High Voltage Unit (200-240V) (H5L) 5 Gallon Low Voltage Unit (100-120V) Now scroll with the (+/-) buttons through the models listed above until the display matches the model you are working with.
13 LEVEL 2 PROGRAMMING H2 - F° OR C° SELECTION 1. T o enter Level 2 Programming, press and hold the upper hidden button until H2 appears on the display . Release the upper hidden button. The display will show either FA H (Degrees in Fahrenheit) or CEn (Degrees in Centigrade).
14 DRAINING THE DISPENSER - OHW CAUTION - The dispenser must be disconnected from the power source throughout these steps. 1. Disconnect the dispenser from the power source and allow dispenser to cool. 2. Tilt dispenser forward over sink. 3. Open faucet.
An important point after buying a device Bunn 10267 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn 10267 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn 10267 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn 10267 you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn 10267 will certainly help you make a decision on the purchase.
If you already are a holder of Bunn 10267, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn 10267.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn 10267. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn 10267 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
