Instruction/ maintenance manual of the product INSTALLATION GUIDE OWNER'S GUIDE Bulldog Security
Go to page of 14
INSTALLATION GUIDE • OWNER'S GUIDE JBS Technologies produces the world's most innovative and reliable car alarms, remote starters, keyless entry systems and starter immobilizers. JBS Technologies is not an importing or distribution company.
YOUR WARRANTY Here's how your warranty works: JBS Technologies warrants to the original customer, and the original car a limited lifetime warranty. Within 12 months of purchase, JBS Technologies will repair or replace, our option, any defective system at no charge.
REMOTE CONTROL STARTER CONTENTS 26 RS700 3 ATTENTION : We urge you to immediately place this card in your wallet. PROGRAMMING FUNCTIONS FOR YOUR WALLET OR GLOVE BOX WARRANTY VALIDATION Mail to: JBS Te.
4 25 SYSTEM FEATURES Four-Button Remotely start your car to run the heater or air Extended Range conditioning from an extended distance. Remote Control Keyless Entry Remotely locks and unlocks your power door locks. Trunk Release Remotely opens your trunk with a push of a button.
24 5 Your system includes: 1-Installation & Operation Guide 1-Main Control Module 1-Four Button Remote Transmitter with Slide Protector 1-(4) Relay Harness with Relays 1-18-Pin Wire Harness 1-Hood.
6 23 It is recommended that a carbon monoxide detector be installed in the living area near the location where the vehicle may be garaged. Since there are many different makes and models of vehicles, look at the wiring chart on our website, www.jbstech.
22 7 MAKING CONNECTIONS 1. Strip back two inches of insulation on the wire from the remote starter. 2. Strip back one inch of insulation on the wire you need to connect to. 3. Separate the vehicle wire as shown. Make the separation large enough to fit the other wire through.
8 21 MAKING CONNECTIONS cont. 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown.
20 9 For wiring charts please visit our website, www.jbstech.com. CONSTANT POWER (+12V, key in any position including off) Make all connections as close to the ignition switch harness as possible. These wire(s) are in your vehicle’s main ignition harness, usually located on the steering column coming from the ignition switch.
10 19 ACCESSORY WIRE(S) THAT POWER THE HEATER/BLOWER MOTOR (+12V in run or on positions) This wire is also in the main ignition switch harness usually located in the steering column. Make all connections as close to the ignition switch harness as possible.
18 11 LOCATING & MAKING CONNECTIONS AUXILIARY INPUT If you wish to use this starter with an aftermarket alarm, connect the BLUE wire from the 18-pin harness to the second or third channel (-) output of your existing alarm. When the output is activated, a (-) signal will be supplied to the remote starter.
12 17 MECHANICAL NEUTRAL SAFETY SWITCH (Rear Wheel Drive Only) When installing a Bulldog remote starter on GM vehicles or Dodge Dakotas built prior to 1996, you must: Use the diagram below to create a circuit that will prevent the remote starter from starting the vehicle unless the key is removed from the ignition switch.
16 13 CONNECTING THE 18-PIN HARNESS & 4-RELAY HARNESS OPTIONAL CONNECTIONS CONNECTING “TYPE B LOCKS” • If your vehicle has a “ Type B ” door locking system, connect the GREEN WITH BLACK STRIPE wire from the 18-pin harness to the door lock wire.
14 15 ANTENNA PLACEMENT FACTORY ANTI-THEFT SYSTEMS FOR GENERAL MOTORS CARS ONLY System 1 : PASSKEY or VATS system (1985 and up). This system has a resistor pill in the key. Measure resistance of the pill using a test meter. A bypass module is available, Module 791.
An important point after buying a device Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE you will learn all the available features of the product, as well as information on its operation. The information that you get Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE will certainly help you make a decision on the purchase.
If you already are a holder of Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE.
However, one of the most important roles played by the user manual is to help in solving problems with Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
