Instruction/ maintenance manual of the product 1402 Bulldog Security
Go to page of 14
INSTALLATION GUIDE OWNER'S GUIDE Keyless Entry and Alarm System Model 1402 BULLDOG SECURITY Creating A Higher Standard Thank you for purchasing an American made product by Bulldog Security . To order additional transmitters or other accessories, visit our website at www.
CONTENTS 3 System Features ...............................................4 - 5 System Components .............................................6 Required Tools .....................................................6 Technical Assistance .
5 SYSTEM FEATURES CONT. On-Board Built-in relay provides a positive (+) Parking parking light output. No relay needed. Light Relay On-Board Door Built-in relay for Type A, Type B and Lock Relay Type C door locks. Plug In Six A visual theft deterrent that flashes when Function LED the system is armed.
7 BEFORE YOU BEGIN CONT. PRECAUTIONS This system will add remote keyless entry features to any vehicle with power door locks. This will also work as a replacement system for the factory installed keyless entry system. Use masking tape to indicate the preferred mounting locations of interior components, LED and override switch.
9 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together. Use this method for all connections.
11 LOCATING & MAKING CONNECTIONS CONT. 3. Turn the ignition ON. Probe for a wire that shows 12 volts only when the ignition is on. Confirm this by turning the ignition on and off while probing each wire. 4. Mark this wire with its function Ignition Power.
13 LOCATING & MAKING CONNECTIONS CONT. CONNECTING THE MAIN WIRING HARNESS TO THE MODULE Carefully plug the main harness into the 1402 module.
CONNECTING THE CAR HORN WIRE You must use optional part #775. MOUNTING AND CONNECTING THE OPTIONAL SIREN Select a location under the hood for the siren. For best results, the location should meet the following conditions: The mounting location should be solid and have no moving parts nearby.
18 TESTING: Door Locks There are four basic types: Type A Door Lock Test (Most GMs and some Chryslers) Probe both of your door lock wires going to the door lock switch usually located in the drivers kick panel. Attach the clip end of your test light to a good chassis ground.
19 TESTING DOOR LOCKS CONT. wires tests (+) positive when lock is pressed and the other tests (+) positive when they are unlocked, your vehicle has a Type A door locking system. Make sure to mark which wire is lock and unlock. Proceed to Connecting Door Locks, Connecting Door Locks.
22 HOW TO USE YOUR REMOTE TRANSMITTER BUTTON #2 OPTION #2 BUTTON #4 BUTTON #1 ARM/DISARM BUTTON #3 OPTION #3 KEYLESS ENTRY FUNCTIONS LOCKING DOORS Press transmitter Button #1 to lock the doors. The parking lights will flash once and the horn or siren will sound acknowledging the unit received the signal.
24 HOW TO USE YOUR REMOTE TRANSMITTER CONT. VALET MODE To activate Valet Mode, first disarm the system. Hold Button #4 for ten (10) seconds and the system will chirp once. Press Button #4 again within two (2) seconds and the system will chirp once again.
26 KEEP THIS MANUAL IN YOUR GLOVEBOX TO USE AS A REFERENCE. CLEARING THE E-PROM MEMORY Take the BLACK wire with the green tag and attach it to a chassis ground (shock or microwave sensor input) white plug with the override switch. Then cycle the ignition key from off to run six times within five seconds.
JBS Technologies, LLC 225 Technology Way Steubenville, OH 43952 Toll Free: 800.878.8007 Fax: 740.282.1201 www.bulldogsecurity.com email: techsupp@bulldogsecurity.com JBS T echnologies produces the world's most innov ative and reliable car alarms, remote starters, keyless entry systems and starter immobilizers.
An important point after buying a device Bulldog Security 1402 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bulldog Security 1402 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bulldog Security 1402 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bulldog Security 1402 you will learn all the available features of the product, as well as information on its operation. The information that you get Bulldog Security 1402 will certainly help you make a decision on the purchase.
If you already are a holder of Bulldog Security 1402, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bulldog Security 1402.
However, one of the most important roles played by the user manual is to help in solving problems with Bulldog Security 1402. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bulldog Security 1402 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
