Instruction/ maintenance manual of the product 9BSST Bryston
Go to page of 16
9B SST P O W E R A M P L I F I E R OWNER’S MANU AL UPDA TED 2007-01-08.
9B SST FIVE CHANNEL POWER AMPLIFIER T able of Contents General Introduction Page 1 Instalation and V entilation Rear Panel Input Settings/Connections Page 2 Setting Input Selector Switch Balance Input.
9B SST FIVE CHANNEL POWER AMPLIFIER 1 Introduction Thank you for choosing the 9BSST Five Channel Power Amplifier . Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier . W e consider you, our customer , to be Bryston’s most important resource, and your opinion is very much appreciated.
9B SST FIVE CHANNEL POWER AMPLIFIER 2 Rear Panel Input / Output Connections 1. Input Select Switch. Each 9BSST channel gives the user the option of switching between either balanced input or single ended input. 2. Balanced Input connector . ( Imp. 20k ) This input connector accepts standard ‘XLR’ or 1/4” TRS .
9B SST FIVE CHANNEL POWER AMPLIFIER 3 6. Output binding posts The RED binding post is connected to the amplifier output . Connect to this post the (+) terminal on the loudspeaker . The BLACK binding post is connected to signal ground . Connect to this post the (-) terminal on the loudspeaker .
9B SST FIVE CHANNEL POWER AMPLIFIER 4 Front Panel 1. 'SST POWER' switch The front panel label 'ST POWER', is a touch sensitive membrane switch used to apply or remove A/C line power to the 9BSST circuitry . Push firmly the center of the switch until the power-up sequence begins.
9B SST FIVE CHANNEL POWER AMPLIFIER 5 Power Control Panel REAR POWER ENTR Y P ANEL 1. Master circuit - breaker . The 9BSST uses a magnetic-trip circuit breaker (1) to protect the amplifier . This switch should be ‘OFF’ when installing the 9BSST . When switched ‘OFF’ all A/C power is removed from the amplifier , including standby power .
9B SST FIVE CHANNEL POWER AMPLIFIER 6 Rack Mounting Instructions Removing the channels makes rack mounting far easier as the chassis will be much lighter . Before removing any screws from the 9BSST be sure the power cord is removed from the unit. Remove the screws indicated on the top and bottom views plus the ones described on the sides.
9B SST FIVE CHANNEL POWER AMPLIFIER 7 T ypical 5.1 Home Theatre Setup Left-Rear Right-Rear Center Powered Subwoofer Left-Front Right-Front HOME THEA TRE PROCESSOR 9BSST 5X120W/CH.
9B SST FIVE CHANNEL POWER AMPLIFIER 8.
9B SST FIVE CHANNEL POWER AMPLIFIER 9 T ypical Band-pass Noise T ypical THD+N Harmonic Content Power supply artifacts are all below -95 dBu balanced input with 23dB gain shown The harmonic content of the 9BSST is all even order. dBu: dB relative to a reference of 0.
T ypical THD+N Sweep 4 ohm 200w 8 ohm 120w T ypical IMD Sweep 8 ohm 120w 4 ohm 200w 9B SST FIVE CHANNEL POWER AMPLIFIER 10 Graph shows that distortion is essentially unaffected by load.
BALANCED INPUT 4 v 1 v 2 v OUTPUT 250W/8 XLR/PHONE INPUT Pin 1/SLEEVE: Pin 2/TIP: Pin 3/RING: GND POS(+) NE G( – ) WARNING! RISK OF HAZARDOUS ENERGY . MAKE PROPER SPEAKER CONNECTIONS. SEE OPERATING MANUAL BEFORE USING. HOME THEATRE SETTINGS BALANCED INPUT: SINGLE ENDED INPUT: See manual for further details.
9B SST FIVE CHANNEL POWER AMPLIFIER 12.
9B SST FIVE CHANNEL POWER AMPLIFIER 15 9B SST FIVE CHANNEL POWER AMPLIFIER 13 T echnical Specifications Power Output 120 watts per channel into 8 ohms 200 watts per channel into 4 ohms Gain Select and Sensitivity 29dB - 1.1Vin = 120W @ 8 Ohms - (1V Position) 23dB - 2.
IMPORT ANT SAFETY INSTRUCTIONS The lightning flash with ar rowhead symbol within an equilateral triangle, is intended to aler t the user to the presence of un-insulated “dangerous voltage “ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons .
An important point after buying a device Bryston 9BSST (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bryston 9BSST yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bryston 9BSST - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bryston 9BSST you will learn all the available features of the product, as well as information on its operation. The information that you get Bryston 9BSST will certainly help you make a decision on the purchase.
If you already are a holder of Bryston 9BSST, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bryston 9BSST.
However, one of the most important roles played by the user manual is to help in solving problems with Bryston 9BSST. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bryston 9BSST along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
