Instruction/ maintenance manual of the product 362AAN Bryant
Go to page of 12
NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. Index Page SAFETY CONSIDERATIONS ..................................................1-2 Minimum Clearance to Combustibles .
Only the latest issues of above codes should be used, and are available from either The National Fire Protection Agency, Bat- terymarch Park, Quincy, MA 02269 or The Canadian Standards Association, 178 Rexdale Blvd., Rexdale, Ontario M9W 1R3 Recognize safety information.
3. Caulking or sealants are applied to areas such as joints around window and door frames; between sole plates and floors; between wall-ceiling joints; between wall panels; at penetrations for plumbing, electrical, and fuel lines; and at other openings.
VENTING INSTRUCTIONS Venting of furnace should be to the outside and in accordance with local codes or requirements of local utility. OIL-FIRED APPLIANCES SHALL BE CONNECTED TO FLUES HAVING SUFFICIENT DRAFT AT ALL TIMES TO ENSURE SAFE AND PROPER OPERATION OF APPLIANCE.
ELECTRICAL The appliance must be installed in accordance with current ANSI/NFPA 70 National Electrical Code, CSA C22.1 Canadian Electrical Code Part 1, and/or local codes. The control system depends on correct polarity of power supply. Connect HOT wire (H) and NEUTRAL wire (N) as shown in Fig.
c. Tighten purge fitting. Allow oil to run to nozzle and fire burner. d. If purging takes longer than 30 sec and no flame has been established, burner stops. Push reset button on top of primary control to restart burner. e. For detailed information on operation of primary control, refer to instructions included with furnace.
The procedure for nozzle installation and/or replacement is out- lined in oil burner instruction manual which came with furnace. For ease of maintenance, the oiling procedure for burner motor, as outlined in burner manual, should be performed at this time.
17. Use a stiff brush and vacuum cleaner to clean inside of primary drum. CAUTION: Never use incendiary type cleaners (smoke sticks) for cleaning! WARNING: For all heat exchanger plates that have been removed, the gaskets MUST be replaced.
INSULATION INTERMEDIATE PANEL FILTER B A G D ELECTRICAL CONNECTIONS OIL INLET F 12 1 ⁄ 16 ″ EH 1 ″ INSULATION PARTITION PANEL SUPPLY DUCT CLEAN-OUT PORTS RETURN DUCT 1 ″ 3 ″ C A96309 DIMENSIONS (IN.
Fig. 6—Barometric Damper Locations A95117 FIG. A FIG. G FIG. D FIG. L FIG. B FIG. C FIG. J FIG. H FIG. K POOR WRONG WRONG WRONG WRONG WRONG BAROMETRIC DAMPER LOCATIONS GOOD LOCATIONS BAD LOCATIONS .
→ Fig. 7—Wiring Diagram A96380 INDOOR BLOWER MOTOR BR BR CAP T GND LINE V 24 V LINE V 24 V BK BL BR GR OR RD RD/BK VI WH YL F T CAP AL L.
USER’S INFORMATION I. HERE’S HOW YOUR HEATING SYSTEM WORKS The furnace operates automatically. It is controlled by a thermostat which you set at the temperature most comfortable to you. When the inside temperature drops below this setting, your thermostat will turn on heating system.
An important point after buying a device Bryant 362AAN (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bryant 362AAN yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bryant 362AAN - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bryant 362AAN you will learn all the available features of the product, as well as information on its operation. The information that you get Bryant 362AAN will certainly help you make a decision on the purchase.
If you already are a holder of Bryant 362AAN, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bryant 362AAN.
However, one of the most important roles played by the user manual is to help in solving problems with Bryant 362AAN. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bryant 362AAN along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
