Instruction/ maintenance manual of the product LAP24EULBA Bretford
Go to page of 33
LAP24EULBA LAP24EULFR NOTEBOOK CART ASSEMBL Y WITH TIMER Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER REPLACEMENT Parts List Qt y .
clip DET AIL 'A' DET AIL 'B' E-Unit power cord timer assembly bottom shelf Front View bracket assembly bracket assembly.
Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
DET AIL 'D' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out.
Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the rear of cart. 3. T ilt in and set bottom in back, in front of rear p anel cutout window .
Step 6 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf.
Step 1 Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DET AIL 'A'). DET AIL 'A' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNPLUG.
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out.
DET AIL 'D' DET AIL 'E' Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Step 4 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf.
Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position.
E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DET AIL 'A').
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out.
DET AIL 'C' DET AIL 'D' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should be visible from rear panel cutout window .
Step 5 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf.
Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the bottom of cart.
clip DET AIL 'A' DET AIL 'B' bracket assembly bracket assembly Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
front-right front-left Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should face the front.
TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET AIL 'A' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AIL 'A').
Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View).
Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . The E-Unit bracket assembly shown above, will need to be removed (with a philips screwdriver) to allow the E- Unit to swing back. This will allow the timer cord plug to pass between the E-Unit and rear panel.
Step 6 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned with rear panel cutout s.
Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf.
SEE DET AIL 'A' SEE DET AIL 'B' bottom shelf TIMER REPLACEMENT : 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 E-Unit power cord timer assembly bottom shelf Front View Open both front doors of cart to access E-Units.
front-right front-left Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
DET AIL 'A' Step 3 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AIL 'A'). DET AIL 'B' mounting tab.
Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly .
Step 6 Remove 2 screws that secure timer to bracket. Step 7 Install bracket to replacement timer with 2 nut s. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . Timer vents & bracket must be attached as shown.
Step 8 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned with rear panel cutouts.
front-right front-left DET AIL 'C' Step 10 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C').
1 1 2 2 1 1 1 1 1 1 22 15 19 11 7 16 20 8 12 AUX. 1 3 AUX. 2 4 17 21 13 9 18 22 10 14 AUX. 3 1 5 AUX. 4 2 6 23 27 24 28 25 29 26 30 AUX. 5 AUX . 6 LABEL INST ALLA TION: E-Unit at front suggested label direction suggested installation of labels peel off and attach corresponding labels to shelves and E-Units.
Part #031-6566 Rev . 12.22.08 CZ P AD LOCK - DOOR: Open Lock The First T ime 1) Set the combination to 0-0-0-0 2) Depress shackle and pull open. T o Set Y ou Own Combination **REMEMBER: Combination can only be set when lock is open. 1) Insert “reset” tool (included in package) in hole on side of lock.
An important point after buying a device Bretford LAP24EULBA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bretford LAP24EULBA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bretford LAP24EULBA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bretford LAP24EULBA you will learn all the available features of the product, as well as information on its operation. The information that you get Bretford LAP24EULBA will certainly help you make a decision on the purchase.
If you already are a holder of Bretford LAP24EULBA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bretford LAP24EULBA.
However, one of the most important roles played by the user manual is to help in solving problems with Bretford LAP24EULBA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bretford LAP24EULBA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
