Instruction/ maintenance manual of the product GT-28, GT-24 Boston Acoustics
Go to page of 19
GT-28 GT-24 2-Channel, High-Curr ent/High-Power Amplifiers.
2 T able of Contents Parts List 3 Features and Specifications 3 Control Functions 4 Control functions (cont.) 5 Mechanical Functions 6 Recessed RCA inputs 6 Control cover r emoval and reinstallation 6 Multi-position mounting feet 6 V ents (side and rear) 6 Mechanical functions (cont.
Included Hardwar e: GT -28 & GT -24 (1) owner’ s manual (1) female quick-connect terminal for remote input (1) 2mm hex wrench (for speaker input) (1) 3mm hex wrench (for power input) (6) mounting screws 3 Parts List Te chnical Specifications GT -28 GT -24 14.
4 12.6–14.4VDC B+ B+ GROUND GND GND FUSE 4 x 25A SPEAKER OUTPUT L R MONO LOWPASS OFF ON HIGHPASS OFF ON 5 0.2 INPUT SENSITIVITY 2.6 50 350 Hz 200 20 350 Hz 185 0.
Lowpass Crossover Contr ols To use lowpass crossover move LOWP ASS switch to righthand position. Lowpass crossover fr equency is adjustable from 50Hz to 350Hz by r otary control.
6 Mechanical Functions Recessed RCA Inputs The input jacks are r ecessed into the body of the amplifier to provide clear- ance in tight mounting locations. Control Cover Removal and Reinstallation The cover panel is secured with two (2) captive coin-slotted scr ews.
7 Mechanical Functions (cont.) Amplifier Linking The design of the side panels enables multiple amplifiers to be used together without additional hardwar e. Wire Connection Amplifier accepts stripped wire dir ectly into the terminal blocks. Speaker outputs accept 8-gauge, and the DC power and ground accept 4-gauge.
8 Before Y ou Install Before you install the unit, disconnect the negative (–) battery cable in the engine compartment of the vehi- cle. Doing so will prevent damage to both the electrical system of the vehicle and the amplifier during installation.
9 57mm (2 1 / 2 ") Choose the Mounting Location Plan your installation so that the amplifier is mounted where adequate ventilation is available. Never mount an amplifier in the engine compartment of a vehicle! W ARNING! Before driving the mounting scr ews thr ough any surface, be sure of what is behind that sur- face.
10 Passenger and T runk Compartment Mounting If the amplifier is mounted under a seat, be sure that the vents do not become blocked. Do not allow seat padding or other obstructive material to press down on the amplifier . All Boston GT amplifiers have top panel controls.
SPEAKER OUTPUT L R MONO Power/B+ and Power/GND Connection Strip approximately 5 / 8 " (16mm) of insulation. The positive (+) power wir e is installed into the amplifier terminal marked “B+”. The negative (–) wire is installed into the terminal marked “GND”.
12 Mono Subwoofer Operation When the amplifier is configured for mono operation, use the speaker output terminals marked for mono use. W ARNING! Subwoofer impedance must not fall below 2 ohms when in MONO mode. Installation—Fuses and Wiring (cont.
13 Setup T uning—Full-Range Speakers (cont.) 4) Head Unit The head unit should have all controls such as bass, tr eble, balance, and fader set to the flat or centered position.
14 8) “Q” Control Once the highpass crossover point has been determined, use the “Q” con- trol to incr ease the bass information centered ar ound the crossover point. Setting the “Q” control is done in conjunction with setting the levels on the input sensitivity and highpass crossover fr equency controls.
15 4) Input Sensitivity Control Tu rn control all the way counterclockwise (minimum position). In this position, the amplifier will be less sen- sitive to the input signal from the head unit. Slowly r otate this control clockwise until maximum undistorted playing level is heard fr om the subwoofer(s).
16 System Examples System A—Full-Range Front Speakers 6 . 5 L F 6 . 5 L F fuse to + battery terminal to gr ound to ground fuse to + battery terminal System B—Rear Fill Speakers fuse to + battery terminal to ground to gr ound fuse to + battery terminal 6 .
17 System Examples (cont.) System C—Parallel 4 Ω Subwoofers (2 Ω load) System D —Series/Parallel 2 Ω Subwoofers (2 Ω load) 10.5LF 4 Ω 10.5LF 4 Ω fuse to + battery terminal to ground to gr ound fuse to + battery terminal fuse to + battery terminal to gr ound to gr ound fuse to + battery terminal 10.
18 Amplifier T r oubleshooting Guide Status LEDs on Amplifier not Lit — Head Unit (Sour ce) T urned “ON” V erify Remote turn-on wire fr om source to amplifier has pr oper voltage Power (B+) c.
19 Contact and W arranty Information 300 J ubilee Drive Pe a b o d y, MA 0 1 960 U.S.A. (978) 538-5000 Boston, Boston Acoustics, and the Boston logo are r egister ed trademarks of Boston Acoustics, Inc. © 2003 Boston Acoustics, Inc. All rights reserved.
An important point after buying a device Boston Acoustics GT-28, GT-24 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Boston Acoustics GT-28, GT-24 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Boston Acoustics GT-28, GT-24 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Boston Acoustics GT-28, GT-24 you will learn all the available features of the product, as well as information on its operation. The information that you get Boston Acoustics GT-28, GT-24 will certainly help you make a decision on the purchase.
If you already are a holder of Boston Acoustics GT-28, GT-24, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Boston Acoustics GT-28, GT-24.
However, one of the most important roles played by the user manual is to help in solving problems with Boston Acoustics GT-28, GT-24. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Boston Acoustics GT-28, GT-24 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
