Instruction/ maintenance manual of the product GT18B01 Bostitch
Go to page of 30
1 GT18B01 HYDRAULIC POWER UNIT S AFETY , O PERA TION AND M AINTENANCE SER VICE MANUAL WARNING Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .
2.
3 T ABLE OF CONTENTS For the nearest authorized and certifi ed dealer , call Stanley Hydraulic T ools at the number listed on the back of this manual and ask for a Customer Service Representative. SERVICING THE ST ANLEY POWER UNIT : This manual contains safety , operation, and routine mainte- nance instructions.
4 CERTIFICATE OF CONFORMITY Hy draulic Tools ______________________________________________________________________ I, the undersigned: Burrows, James Surname and First names Hereby certify that the c onstruction plant or equipment specif ied hereunder: 1.
5 Safety symbols and signal words, as shown below , are used to emphasize all operator , maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equip- ment.
6 T ool operators and maintenance personnel must always comply with the safety precau- tions given in this manual and on the stickers and tags attached to the equipment. These safety precautions are given for your safety . Review them carefully before operat- ing the tool and before performing general maintenance or repairs.
7 T OOL STICKERS & T AGS 65458 Sound Power Decal 62302 Power Unit Dash Decal 62300 CHOKE D ANGER PULL TO ST ART PUSH TO R UN 62300 Single Circuit 28322 CE Decal AUTO IDLE OFF AUTO IDLE ON R U 6230.
8 HOSE TYPES Hydraulic hose types authorized for use with Stanley Hydraulic T ools are as follows: ➊ Certifi ed non-conductive ➋ Wire-braided (conductive) ➌ Fabric-braided (not certifi ed or labeled non-conductive) Hose ➊ listed above is the only hose authorized for use near electrical conductors.
9 HTMA REQUIREMENTS FLOW RA TE TOOL OPERA TING PRESSURE (at the power supply outlet) SYSTEM RELIEF V AL VE SETTING (at the power supply outlet) MAXIMUM BACK PRESSURE (at tool end of the return hose) Measured at a max. fl uid viscosity of: (at min. operating temperature) TEMPERA TURE Suffi cient heat rejection capacity to limit max.
10 Chevron A W-MV -32 Exxon "Univis" J-26 Mobil D.T .E. 13 Gulf "Harmony" AW -HVI-150-32 Shell "T ellus" T -32 T exaco "Rando" HD-AZ Union "Unax" AW -WR-32 T erresolve EnviroLogic 132 4. HYDRA ULIC CONNECTIONS The recommended hose length is 25 ft/8 m with a 1/2 inch/12.
11 CONTROL P ANEL RETURN PRESSURE H.T .M.A. 1/2 INCH MALE QUICK DISCONNECT COUPLER H.T .M.A. 1/2 INCH FE- MALE QUICK DISCON- NECT COUPLER 1/2 INCH I.D. HOSE, 25 FT LONG WITH 2500 PSI/ 172 BAR RA TING AND 4 T O 1 SAFETY F ACTOR PRESSURE RETURN 1/2 INCH MALE PIPE HOSE END 1/2 INCH MALE PIPE HOSE END ADAPTER, 3/8 INCH MALE PIPE x -8 SAE O-RING H.
12 CONTROLS This unit is equipped with an advanced proportional engine control system. It provides a means of controlling engine speed by adjusting the fuel control lever with an actuator .
13 OPERA TION COLD WEA THER ST ARTUP 1. Use the procedures described under "ST ARTUP" and then follow the procedure below . 2. Hydraulic fl uids are thicker in cold weather . Therefore, it is recommended that the engine be run at low idle long enough to bring the fl uid temperature up to a minimum of 50°F/10°C.
14 ST ORAGE • Clean the unit thoroughly before storage. Do not use water pressure. • Always store the unit in a clean and dry facility . • If the unit will be stored for a prolonged period (over 30 days), add a fuel additive to the fuel tank to prevent the fuel from gumming.
15 CHECKING PERFORMANCE CONTROL™ (ELECTRONIC GOVERNOR-ST A TIC CHECK) T o determine whether a governor problem is being caused by the actuator or the control module, perform the following static check exactly in order shown. A pair of jumper wires and a known good 12-volt battery is required.
16 F AUL T CODES 1 APECS unit not calibrated yes Have engine serviced by an Authorized Stanley Dealer . 2 Engine speed excessive yes Have engine serviced by an Authorized Stanley Dealer . 3 Engine speed unusually low yes Have engine serviced by an Authorized Stanley Dealer .
17 GENERAL T ests and adjustments should be performed periodically to ensure the power unit is operating at maximum effi ciency . Stanley Circuit T ester (part number 04182) is recommend- ed. This tester can be used to isolate problems in both the engine and hydraulic system prior to any power unit disas- sembly .
18 Engine will not start. Flow selector switch not in the Make sure the fl ow selector switch is in OFF position. the OFF position when starting. Battery not connected. Attach battery cables, check wires. Weak battery . T est battery , charge or replace.
19 Engine: ....................................................................................................................... ........................................ 18 hp Briggs Capacity .........................................................
20 SER VICE GENERAL Service instructions in this section are limited to parts and components other than the engine and hydraulic pump. Other major components should be serviced by representa- tives of.
21 Be sure the tapered cone surfaces of the bushing and blower hub are clean and free of anti-seize lubricants. CA UTION 2. Disconnect the wiring harness (See Figure 4, Wiring Diagrams for the correct connections). 3.Follow steps 1 through 4 under "Manifold Assembly Re- moval".
22 Assemble the bushing and blower hub with the bolts inserted (but not tightened) through the drilled holes in the blower hub and into the tapped holes in the bushing. With the key in the shaft, slide assembly into position on the shaft and tighten the setscrew over the key (if equipped).
23 SER VICE HYDRAULIC T ANK, COOLER & FIL TER ASSEMBL Y (see fi gure 1, 2 & 3) 1. First remove the hydraulic fl uid from the tank by either pumping it out with a portable drill pump or draining it into a container . 2. Remove the cooler guard (20, fi g.
24 FIGURE 1. BRIGGS ENGINE ASSEMBL Y 5 6 3 5 3 7 3 4 3 6 5 2 4 4 2 7 5 0 5 1 8 2 6 2 8 4 5 3 0 4 3 3 0 4 7 3 3 3 1 3 0 3 2 2 9 4 9 4 8 1 7 1 6 1 4 1 3 1 2 1 1 9 1 0 4 1 5 2 0 2 1 2 3 1 8 2 5 2 2 1 9 4.
25 ITEM P/N Q T Y DESCRIPTION 1 36150 1 Muffl er 1A 65456 1 Spark Arrester 2 36151 1 Heat Shield 3 36152 2 Screw , Hex W asher 4 59007 1 Briggs Engine 5 56656 1 Coupling 6 07819 1 Square Key 7 07860 .
26 FIGURE 2. FRAME P ARTS ITEM P/N Q T Y DESCRIPTION 1 370502 7 Capscrew , 5/16 in. -18 UNC 2 03906 7 Nylock Nut, 5/16 in. -18 UNC 3 62270 1 Handle, Rear Lift 4 58857 1 Coupler , Male 3/8 in., -8 SAE 5 58856 1 Coupler , Female 3/8 in., -8 SAE 6 60962 2 Capscrew , 1/4 in.
27 ITEM P/N QTY DESCRIPTION 1 59130 1 Manifold Assy , Single Circuit 2 59104 1 Hose Barb, 3/4 in. Hose x 3/4 in. Pipe 3 62199 4 Hose Clamp 4 350000 1 Elbow , 45° Straight Thread 5 02773 1 Adapter 6 5.
28 RECTIFIER WIRE WHITE CONTROLLER TO MAGNETO WIRE ON ENGINE GRA Y WIRE OIL PRESSURE SWITCH FUEL SHUTOFF RED WIRE - THROTTLE CONTROL SWITCH (NOTE: PLUG BEHIND SWITCH WITH BLUE & YELLOW WIRES GOES .
29 Stanley Hydraulic T ools (hereinafter called “Stanley”), subject to the exceptions contained below , warrants new hydraulic tools for a period of one year from the date of sale to the fi rst r.
30 Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .stanley-hydraulic-tools.com.
An important point after buying a device Bostitch GT18B01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bostitch GT18B01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bostitch GT18B01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bostitch GT18B01 you will learn all the available features of the product, as well as information on its operation. The information that you get Bostitch GT18B01 will certainly help you make a decision on the purchase.
If you already are a holder of Bostitch GT18B01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bostitch GT18B01.
However, one of the most important roles played by the user manual is to help in solving problems with Bostitch GT18B01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bostitch GT18B01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
