Instruction/ maintenance manual of the product PRS926F70E Bosch
Go to page of 20
bitte aufbewahren veuillez conserver si prega di conservarle please keep por favor , guardar por favor , guardar lütfen saklayýnýz Assembly instructions Einbauanleitung Notice de montage Istruzioni.
2 4 4a 4b 3 70.
8 5 6 7 8 7a 7c 8a 7b.
9.
10 10 a 11.
en Read the appliance's instructions before installing and using. The graphics in these Assembly instructions are given as a guide only. The manufacturer is exempt from all liability if this manual's requirements are not complied with.
Changing the inner flame nozzle (fig. 9b): - Unscrew the part M3 from the threaded part M2; to do this, hold the threaded part in the opposite direction. - Remove the pipe from the part M2. Fig. b2. - Disassemble the assembly of parts M2 and M4 from part M1.
werden, die verschlossen werden könnten. Wenn ein horizontaler Gasanschluss hergestellt werden soll, liefert Ihnen unser technischer Kundendienst einen Winkel mit der Teilenummer 173018, sowie eine Dichtung mit der Teilenummer 034308. Abb. 4b. Hinweis! Nach Arbeiten an einer Anschlussstelle, diese immer auf Dichtheit prüfen.
pas être installé dans des yachts ou des caravanes. La garantie ne sera valable que si l'usage pour lequel il a été conçu a été respecté. Avant l'installation, vous devez vérifier que les conditions de distribution locale (nature et pression du gaz) et le réglage de l'appareil sont compatibles (voir tableau I).
- Visser le nouvel injecteur flamme extérieure. Fig. a3-a4, selon le tableau II. - Régler la distance L2 sur la douille de régulation du débit d'air conformément à la valeur -Z- indiquée dans le tableau II. Fig. a5. - Serrer la vis de fixation.
Nel caso in cui occorra realizzare il raccordo del gas in orizzontale, presso il nostro servizio tecnico si possono trovare un gomito, con il codice 173018, ed un giunto con il codice 034308. Fig. 4b. Attenzione! Se si manipola qualunque tipo di raccordo, verificarne la tenuta.
Antes de la instalación Este aparato corresponde a la clase 3, según la norma EN 30-1-1 para aparatos a gas: aparato encastrado en un mueble. Los muebles próximos al aparato deben ser de materiales no inflamables. Los revestimientos estratificados y la cola que los fija, deben ser resistentes al calor.
A: apretar los tornillos bypass a fondo. B: aflojar los tornillos bypass hasta la correcta salida de gas de los quemadores: compruebe que al ajustar el mando entre el máximo y el mínimo, el quemador no se apaga ni se crea retroceso de llama. C: los tornillos bypass deben ser cambiados por un técnico autorizado.
- Mude os injectores usando a chave disponível através do nosso serviço de assistência técnica, com o código 424699, tendo especial atenção para que não se solte o injector ao retirá-lo ou fixá-lo no queimador. Aperte bem os injectores para garantir a hermeticidade.
Vernis voor houten werkvlakken de snijvlakken met een speciale lijm, om deze te beschermen tegen vocht. Installatie van het apparaat De klemmen en de zelfklevende pakking (onderrand van de kookplaat) zijn in productie geplaatst, verwijder deze onder geen enkele voorwaarde.
Opgelet! Plaats ten slotte de sticker die het nieuwe gastype aanduidt, dichtbij het gegevensplaatje. tr Cihaz ı kurmadan veya kullanmadan önce talimatlar ı okuyunuz.
- Ana brülör ucuna kolayca eri ş mek için ba ş l ı ğ ı tersi yönde çevirerek serbest b ı rak ı p ba ğ lant ı vidas ı n ı gev ş etiniz. Ş ekil a1. - D ı ş alev brülör ucunu sola do ğ ru çevirerek ç ı kart ı n ı z. Ş ekil. a2-a3.
(034308), поставляемые с варочной панелью . Рис . 4a. В этом случае необходимо исключить соприкосновение шланга с п.
I COUNTRIES/GA SES GA S A DJUSTED MODEL T YPE G20, G25, G30, G31 G25.1 G20 (m3/h) G25 (m3/h) G25.1 (m3/h) G30 (g/h) G31 (g/h) W V~ Hz ER926SB70 N HSE-K9F4L30 13,70 - 1,306 1,519 - 994 978 0,8 W 220-24.
II III Cod. 9000346885 J G20/20 G20/25 G25/20 G 25/25 G25.1/25 G30/29 G30/37 G30/50 G31/37 G20/20 D D D D A C C A G20/25 D D D D A C C A G25/20 D D D D A C C A G25/25 D D D D A C C A G25.
An important point after buying a device Bosch PRS926F70E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bosch PRS926F70E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bosch PRS926F70E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bosch PRS926F70E you will learn all the available features of the product, as well as information on its operation. The information that you get Bosch PRS926F70E will certainly help you make a decision on the purchase.
If you already are a holder of Bosch PRS926F70E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bosch PRS926F70E.
However, one of the most important roles played by the user manual is to help in solving problems with Bosch PRS926F70E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bosch PRS926F70E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
