Instruction/ maintenance manual of the product 1293d Bosch Power Tools
Go to page of 24
Operating/Safety Instructions Consignes de fonctionnement/sécurité Instrucciones de funcionamiento y seguridad IMPORTANT: IMPORTANT : IMPORTANTE: Read Before Using Lire avant usage Leer antes de usa.
-2 - Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
-3- Do not use tool if switch does not turn it “ON” or “OFF”. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool.
-4- I MPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
-5- Functional Description and Specifications Disconnect the plug from the power source before making any assembly, adjustments or changing accessories .
Always disconnect the plug from the power source before attaching or removing abrasive sheets. ATTACHING ABRASIVE SHEET 1. To open sanding sheet clamp, pull clamp lever out of its recess and lower as shown in (Fig.
-7- DUST EXTRACTION The integral dust extraction system collects sanding dust in the dust bag. For maximum efficiency, cloth bags should be emptied when they are no more than half full, and should be replaced when the surface becomes clogged with dust or efficiency will be reduced.
-8- Service Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station.
-9- Vous devez lire et comprendre toutes les instructions. Lenon-respect, même partiel, des instructions ci-après entraîne un risque de choc életrique, d'incendie et/ou de blessures graves.
-10- N'utilisez pas un outil si son interrupteur est bloqué. Un outil que vous ne pouvez pas commander par son interrupteur est dangereux et doit être réparé. Débranchez la fiche de l'outil avant d'effectuer un réglage, de changer d'accessoire oude ranger l'outil.
-11- Symboles Important : Certains des symboles suivants peuvent être utilisés sur votre outil. Veuillez les étudier et apprendre leur signification. Une interprétation appropriée de ces symboles vous permettra d'utiliser l'outil de façon plus efficace et plus sûre.
-12- Description fonctionnelle et spécifications Débranchez la fiche de la prise de courant avant d'effectuer quelque assemblage ou réglage que ce soit ou de changer les accessoires. Ces mesures de sécurité préventive réduisent le risque d'une mise en marche accidentelle de l'outil.
-13- Consignes de fonctionnement GÂCHETTE DE COMMANDE MARCHE/ARRÊT Pour mettre l’outil en marche, appuyez sur la gâchette. Pour mettre l’outil à l’arrêt, relâchez la gâchette qui est à ressort et reviendra automatiquement à la position d’arrêt (fig.
-14- POIGNÉE AVANT Votre ponceuse est équipée d’une poignée avant amovible pour poncer dans des espaces restreints. Pour retirer la poignée, enlevez la vis à l’aide d’une clé allen fournie. Reposez toujours la poignée pour un fonctionnement normal.
-15- Entretien L’entretien préventif effectué par des employés non autorisés peut entraîner un positionnement erroné des composants et des fils internes, et ainsi causer des dangers sévères.
-16- Lea y entienda todas las instrucciones. El incumplimiento de todas las instrucciones indicadas a continuación puede dar lugar a sacudidas eléctricas, incendios y/o lesiones personales graves.
-17- correcta hará el trabajo mejor y con más seguridad a la capacidad nominal para la que está diseñada. No utilice la herramienta si el interruptor no la enciende o apaga. Toda herramienta que no se pueda controlar con el interruptor es peligrosa y debe ser reparada.
-18- Símbolos Importante: Es posible que algunos de los símbolos siguientes se usen en su herramienta. Por favor, estúdielos y aprenda su significado. La interpretación adecuada de estos símbolos le permitirá utilizar la herramienta mejor y con más seguridad.
-19- Descripción funcional y especificaciones Desconecte el enchufe de la fuente de energía antes de realizar cualquier ensamblaje o ajuste, o cambiar accesorios. Estas medidas de seguridad preventivas reducen el riesgo de arrancar la herramienta accidentalmente.
-20- Instrucciones de funcionamiento INTERRUPTOR GATILLO “ON/OFF” (DE ENCENDIDO Y APAGADO) Para encender la herramienta (posición “ON”), apriete el interruptor gatillo. Para apagar la herramienta (posición “OFF”), suelte el interruptor gatillo que está accionado por resorte y volverá a la posición “OFF” automáticamente (Fig.
-21- MANGO DELANTERO La lijadora está equipada con un mango delantero extraíble para poder para lijar en espacios reducidos. Para quitar el mango, saque el tornillo con la llave allen suministrada. Vuelva a instalar siempre el mango para la utilización normal.
-22- Servicio El mantenimiento preventivo realizado por personal no autorizado pude dar lugar a la colocación incorrecta de cables y componentes internos que podría constituir un peligro serio.
-23-.
2 609 931 644 1/03 Printed in Switzlerland LIMITED WARRANTY OF BOSCH PORTABLE AND BENCHTOP POWER TOOLS Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all BOSCH portable and benchtop power tools will be free from defects in material or workmanship for a period of one year from date of purchase.
An important point after buying a device Bosch Power Tools 1293d (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bosch Power Tools 1293d yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bosch Power Tools 1293d - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bosch Power Tools 1293d you will learn all the available features of the product, as well as information on its operation. The information that you get Bosch Power Tools 1293d will certainly help you make a decision on the purchase.
If you already are a holder of Bosch Power Tools 1293d, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bosch Power Tools 1293d.
However, one of the most important roles played by the user manual is to help in solving problems with Bosch Power Tools 1293d. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bosch Power Tools 1293d along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
