Instruction/ maintenance manual of the product CAT21 Acumen
Go to page of 12
User Guide IMPORTANT - Make sure you set up your Personal Identification Number (PIN) read Section 16 on page 8. IMPORTANT - Make sure you know where your System Fuse and Spare Fuse are located.
Index 1 System overview 2 The remote transmitter 3 Customising the system 4 Section 1. Full Mode Section 2. Convenience Mode Section 3. Service Mode Section 4. Diagnostic Mode Section 5. Different siren tones Section 6. Customising Audible warning of Arm/Disarm Section 7.
System Over view 2 The Acumen CA T21 consists of the following main components; • Installed CA T21 main unit • 2 x remote transmitters • Installed protecting switch • Installed system fuse and spare fuse • LED system indicator Be sure that you know: 1 1 .
The Remote T ransmitter 3 Ignition key The system is supplied with 2 transmitter/Ignition keys, if a new transmitter is supplied, a new key can be attached as shown in the diagram opposite.
Customising the system 4 Section 1. Full Mode The unit will arm, in it's default setting, 50 seconds after the ignition is turned off and will only detect an ignition on signal. T o passively arm the system automatically with all functions enabled simply fix the Y ellow wire from the alarm to a suitable earth (ground) point.
Customising the system 5 Section 4. Diagnostic Mode Diagnostic Mode will let the system tell you why it has been reacting. If you experience alarms, it helps to know why . The CA T21 system will tell you. Entering Diagnostic Mode is the same as entering Service Mode.
6 Customising the system Section 7. Hazard (4-way flasher) Mode With the motorcycle ignition off, system armed or disarmed, Hold the ‘key’ and ‘P’ button down simultaneously for approx 3 secs.
Customising the system 7 Section 11. Remote T ransmitter battery low war ning. Whenever the remote transmitter is used, the alarm monitors the state of the transmitter’ s batteries. When the batteries start to become discharged, the CA T21 will tell you with 6 rapid beeps every time the key fob is used.
Customising the system 8 Section 16. PIN Override If you cannot disarm the system from the remote transmitter - see troubleshooting, - you will be able to disarm the system by using the Personal Identification Number (PIN). The CA T21 system leaves the factory with no PIN override in its memory .
Customising the system 9 E E N N T T E E R R I I N N G G A A N N E E W W P P I I N N W W H H E E N N A A P P I I N N I I S S A A L L R R E E A A D D Y Y K K N N O O W W N N . . From time- time you may wish to change the PIN that is in the system. 1. Disarm the system 2.
T r oubleshooting 10 The Acumen CA T21 is manufactured using automotive specification parts, including a waterproof connector , and is fully encapsulated to provide protection against water and vibration. The system relies on various signals to make it function correctly and any one of these signals may cause false reactions.
Maintenance 11 T T r r a a n n s s m m i i t t t t e e r r The transmitter contains delicate electronic circuitry . Do not subject to excessive shock, heat, or immersion in water . Replace the batteries when you here a burst of rapid beeps from the CA T21 system upon use of the transmitter .
An important point after buying a device Acumen CAT21 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Acumen CAT21 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Acumen CAT21 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Acumen CAT21 you will learn all the available features of the product, as well as information on its operation. The information that you get Acumen CAT21 will certainly help you make a decision on the purchase.
If you already are a holder of Acumen CAT21, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Acumen CAT21.
However, one of the most important roles played by the user manual is to help in solving problems with Acumen CAT21. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Acumen CAT21 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
