Instruction/ maintenance manual of the product NTC-265-PI Bosch Appliances
Go to page of 28
IP Camera 200 Series NTC-265-PI en Installation Manual.
.
IP Camera 200 Series Table of Cont ents | en 3 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 T able of Contents 1S a f e t y 5 1.1 Safety precautions 5 1.2 Important safety instructions 6 1.3 FCC & ICES compliance 7 1.4 UL certification 8 1.
4 en | Table of Contents IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 6 Maintenance 24 6.1 Repairs 24 6.1.
IP Camera 200 Se ries Safety | en 5 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 1S a f e t y 1.1 Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product.
6 en | Safety IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 1.2 Impor tant safe ty instructions Read, follow, and retain for future reference all of the following safety instructions. Heed all warnings on the unit and in the operating instructions be fore operati ng the unit.
IP Camera 200 Se ries Safety | en 7 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 1.3 FCC & ICES compliance FCC & ICES Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules .
8 en | Safety IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems The user may find the following booklet, prepared by the Federal Communications Commission, helpfu l: How t o Ident ify and Resolve Radio-TV I nterference Problems .
IP Camera 200 Se ries Safety | en 9 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 1.6 Copyrights The firmware 4.1 uses the fonts "Adobe-Helvetica-Bold-R- Normal--24-240-75-.
10 en | Introduction IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 2 Introduction 2.1 F ea tures The Bosch NTC-265-PI 7 20p infrared IP bullet camera is a ready- to-use, robust network camera. This camera offers a cost effective so lution for a broad ra nge of applications.
IP Camera 200 Series Introduction | en 11 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 2.2 Unpacking Unpack carefully and handle the equipment with care.
12 en | Installation IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 3 Installation 3.1 Assembly The sun hood on the camera/housing unit can be adjusted. To adjust the sun hood proceed as follows: 1. Using the special screwdriver bit supplied, loosen the top adjustment screw (1) in the housing.
IP Camera 200 Se ries Installation | en 13 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 3.2 Mounting Figu re 3.1 Mounting the camera To mount the camera to a wall or ceiling: 1. Stick the supplied installation paper sticker to the surface taking care to orientate it correctly.
14 en | Installation IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 3.3 Ne twork (and pow er) connect or Figure 3.2 Ne twork connection – Connect the camera to a 10/100 Base-T network. – Use a shielded UTP Category 5 e cable with RJ45 connectors.
IP Camera 200 Se ries Installation | en 15 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 3.4 Po wer connection The camera can accept power from both the DC12V power input and the Ethernet input at the same time. You can remove either one of the power sourc es without interrupting camera operation.
16 en | Installation IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 3.5 I/O connector Figure 3.4 I/O connector pins – Cut back 5 mm (0.2 in) of insulation. – Relay switching capability: Ma x. voltage 24 VAC or 24 VDC.
IP Camera 200 Se ries Installation | en 17 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 3.6 Audio connectors Figu re 3.5 Audio connectors Connect audio devices to the Line In and Line Out connectors.
18 en | Installation IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 3.7 Camera se t-up To help set up the camera, connect a monitor to the BNC connector of the camera cable tree. This connector provides a composite video signal (with sy nc) for installation purposes only.
IP Camera 200 Se ries Installation | en 19 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 3.7.1 Camera positioning The camera position can be adjusted along three axes. When adjusting ensure that the picture di splay on the monitor is level.
20 en | Installation IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 3.8 Reset ting the camer a If the camera cannot be connected because the IP address has changed, short circuit the reset connector for approximately 7 seconds to recall the factory default values.
IP Camera 200 Series Brow ser connection | en 21 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 4 Bro wser connection A computer with Microsoft Internet Ex plorer can be used to receive live images from the camera, control cameras, and replay stored sequences.
22 en | Brow ser connection IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 4.2 Establishing the connection The camera must be assigned a valid IP address to operate on your networ k. The default addr ess pre-set at the factory is 192.
IP Camera 200 Se ries T r oubleshooting | en 23 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 5 T rouble shooting 5.1 Resolving pr oblems The following table is intended to help identify the causes of malfunctions and correct them when possible.
24 en | Maint enance IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 6 Maintenance 6.1 Repairs 6.1.1 Transfer and disposal The camera should only be pa ssed-on together with this installation guide. The unit co ntains environmentally hazardous materials that must be disposed of according to law.
IP Camera 200 Se ries T echnical Data | en 25 Bosch Security Systems Installation Manual AM18-Q0610 | v1 | 2012.02 7 T echnical Data 7.1 Specificat ions Input voltage +12 VDC or Power-over-Ethernet Power consumption 6.72 W (max) Sensor type ¼-inch CMOS Sensor pixels 1280 x 800 Sensitivity 0.
26 en | T echnical Data IP Camera 200 Series AM18-Q0610 | v1 | 2012.02 Installation Manual Bosch Security Systems 7.1.1 Accessories Contact a Bosch representative in your area for the latest available accessories or visit our we bsite at www.boschsecurity.
.
Bosch Security Systems www.boschsecurity.com © Bosch Security Systems, 2012.
An important point after buying a device Bosch Appliances NTC-265-PI (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bosch Appliances NTC-265-PI yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bosch Appliances NTC-265-PI - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bosch Appliances NTC-265-PI you will learn all the available features of the product, as well as information on its operation. The information that you get Bosch Appliances NTC-265-PI will certainly help you make a decision on the purchase.
If you already are a holder of Bosch Appliances NTC-265-PI, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bosch Appliances NTC-265-PI.
However, one of the most important roles played by the user manual is to help in solving problems with Bosch Appliances NTC-265-PI. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bosch Appliances NTC-265-PI along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
