Instruction/ maintenance manual of the product 241E Bock Water heaters
Go to page of 8
which could occasionally exceed 120 o F . The variation in outcoming temperature could be based on factors in - cluding but not limited to usage patterns and type of installation. T est your water at the tap nearest to the wa- ter heater . W ARNING: Hotter water increases the risk of scald in- jury .
–2– PERFORMANCE SPECIFICA TIONS AND ROUGHING-IN DIMENSIONS Leave ample room for servicing when the water heater is in- stalled – do not block access to the burner , inspection door , handholes or controls. Leave room to pipe the unit and connect the fuel and electricity .
–3– Care must be taken to insure an adequate air supply for the water heater . A . Install equipment only where the water heater will have satisfactory combustion, proper venting, and the maintenance of temperature at safe limits all around the unit under normal operating con- ditions.
–4– 2. Bock recommends a two-pipe (suction and return) system for these heaters. Use 1/2" O.D. soft cop- per tubing (5/8” O.D. soft copper on Sun T ec H pumps) and install a bypass plug on two-pipe system. (See instructions packed with pump.
–5– locking out while bleeding, attach a jumper between the flame detector terminals after starting the burn- er (remove the jumper when done). Double-check control settings as described previously . 1. Start the burner and adjust draft to the -.02 in H 2 O to -.
–6– Carlin burner w/ Carlin EZ-T emp Models 72E, 73E, 190E, 241E, 361E, 541E FIGURE 3 L4006A L 4080B L 8106 W A YNE Models 73E - 541E FIGURE 5 W ayne Model 72E FIGURE 4 W ayne burner w/ Carlin EZ-.
–7– OIL-FIRED W A TER HEA TER MODELS 72E, 73E, 190E, 241E, 361E & 541E This is a tank assembly parts list. When ordering repair parts, always give the part name, heater number (size) and serial number . ITEM DESCRIPTION ITEM DESCRIPTION 1. Cold water inlet dip tube (not on 541E) 2.
LIMITED W ARRANTY W ARRANTY COVERAGE: This warranty covers “Bock” W ater Heater models 72E, 73E, 190E, 241E, 361E and 541E. Bock W ater Heaters, a division of Bock Corporation – a Wisconsin corporation – at 1 10 S.
An important point after buying a device Bock Water heaters 241E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bock Water heaters 241E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bock Water heaters 241E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bock Water heaters 241E you will learn all the available features of the product, as well as information on its operation. The information that you get Bock Water heaters 241E will certainly help you make a decision on the purchase.
If you already are a holder of Bock Water heaters 241E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bock Water heaters 241E.
However, one of the most important roles played by the user manual is to help in solving problems with Bock Water heaters 241E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bock Water heaters 241E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
