Instruction/ maintenance manual of the product 8752 Bloomfield
Go to page of 26
PRINTED IN UNITED STATES OF A MERIC A 605 OWNERS M A NUAL for INTEGRITY™ 5-WARMER COFFEE BREWERS MOD EL : 8752 8752KFT Includes: Installation Operation Use & Care Servicing Instructions Model 8752 Brewer with optional 8900-Series Decanters p/n 70988 Rev.
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery.
MODEL STYLE VOLTS WAT TS AMPS 1ø POWER SUPPLY CORD 8752 8752KFT Decanter Brew er 5 W arm ers 115/230 4000 19.4 None provided Wire directly to cir cuit 1 TABLE OF CONTENTS SPECIFIC ATIONS Thank You for purc hasing this Bloomfield Industries appliance.
FE AT U R E S AN D O P E R AT I N G CO N T R O L S 2 Fig. 1 Model 8752 Features and Operating Controls 605 70988 Ow ners Manual Integrity 5 W Decanter Brew er.
PRECAUTIONS A ND GENERAL INFOR M ATION 3 WARNING: ELECTRIC SHOCK H AZARD All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which requ ire the use of tools. Failure to heed this warning can result in electrical shock.
INSTALL ATION 4 RE A D THIS CAREFULL Y BEFORE ST A RTING THE INST AL L A TION REFER TO EXPLODED VIE W S FOR COMPONENT NAMES/ NUMBERS Unpack the unit. Inspec t all components f or completeness and condition. Ensure that all packing materials have been removed from the unit.
INSTALLATION (continued) 5 NOTE: This equipment must be installed to comply with applicable federal, state an d local plum bing codes an d ordinanc es. WARNING: SHOCK HAZARD Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide suc h a ground .
OPERATION Fig. 4 Brewer Operation Diagram START-UP For initial start-up, or if the br ewer has not been used for an extended period of t ime: ♦ Be sure spray disk and bre w gasket are properly installed in the brew head. ♦ Be sure the water supply is prope rly conne cted and the w ater supply valve is turned ON .
OPERATION (continued) Water temperat ure is sensed by a thermobulb insert ed into the water tank. This temperature signal is fed to the thermostat, which controls line power to the heating elemen t. The setpoint temperature is adjustable at the therm ostat.
BREWING COFFEE CAUTION: BURN HAZARD Exposed surfaces of the brewer, brew chamber and decanter m ay be HOT to the touch, and can cause serious burns. CAUTION: BURN HAZARD To avoid splashing or overf lo wing hot liquids , ALWAYS place an empty decanter under the brew chamber before starting the brew cycle.
CLEANING I NSTRUCTIONS PROCEDURE: Clean Coffee Brewe r PRECAUTIONS: Disconnect brewer fro m electric power. Allow brewer to cool. FREQUENCY: Daily TOOLS: Mild Detergent, Clean Soft Cloth or S ponge Bristle Brush, Bottle B rush 1. Disconnect brewer from electric pow er.
10 TROUBLESHOOTING SUGGESTIONS SUGGESTED REMEDY Check po wer supply cord Check / reset circuit breaker Set for desired temperature Allow to cool Reset hi-limit Examin e wiring & connec tors, therm.
SERVICING IN STRUCTIONS CAUTION: SHOCK HAZARD Opening acce ss panels o r remov ing warmer plat es on this brew ma y expose uninsul ated electrical co m ponents.
SERVICING INST RUCTIONS (continued) TEMPERATURE ADJUSTMENT Unplug power cord or turn circuit breaker OFF. Remove top panel. Pull vent tube o ut of tank lid and inse rt a thermometer of known accuracy in hole. Reconnect brewer to electrical powe r. Place empty cont aine r under bre w chamber.
SERVICING INSTRUCT IONS (continued) 13 IMPORTA NT: Water pressure must be betwee n 20 p.s.i and 90 p.s.i. flowing pressure. If wate r pressure ex ceeds this value, or if water pressure varies g reatly, a pres sure regulator must be installed in the w ater s upply line.
SERVICING IN STRUCTIONS (continued) 14 REPLACE SOLENOID Symptom: Automatic brewer will not flo w water; or, automatic brewer drips continuously from brew head. Unplug po wer cord or t urn circ uit break er OFF . Turn OFF and disconnect water supply from brewer inlet fitting.
REPLACE TIMER A SSEMBLY Unplug power cord or turn circuit breaker OFF. Remove front panel. Remove knob and three screws holding timer to bracket. Disconnect wiring to timer.
CAUTION: CHEMICAL BURN HA ZARD Deliming chemicals may be caustic. Wear appropriate protective gloves and goggles during this procedure. Never siphon deliming chemicals or solutions by mou th. This operation should only be perfo rme d by qualified and experienced service personnel.
7. Set the tank back into the bre wer. Reassemble the tank lid to the water tank. Mak e sure the gasket is properly in place, then reinstall lid clamps. 8. Reinstall wiring to heating el em ent and therm ostat. Reassemble piping for the faucet. Veri fy that all internal components are dry , then reinstall the top panel.
EXPLODED VIEW & PARTS LIST 18 CA BIN ET ASSEMBLY ITEM PART NUMBER DESCRIPTION 1 8700-16 PLATE, WARMER COVER 4 8543-80 CLIP, MOUNTING 23 BUSHING, HEYCO 1/78 33 8543-42 GASKET, SPRAYHEAD 34 82727 SP.
EXPLODED VIEW & PART S LIST (continued) 19 ELECTRICAL COMPONENTS ITEM PA RT NU MBER DESCRIPTION 2 8572-18 ELEMENT, WARMER 120V 100W 30 8707-55 SW IT C H , BR EW (M O ME N T A RY ) 31 8528-40 SWITC.
EXPLODED VIEW & PARTS LIST 20 HOT WATER TANK ASSEMBLY ITEM PART NUMBER DESCRIPTION 13 8043-5 HOLD-DOW N STRAP 14 8942-92 NUT 8-32 HEX KEPS 50 86280 T HERMOSTAT 199ºF 54 8043-12 GASKET, TANK COVER.
EXPLODED VIEW & PART S LIST (continued) 21 PLUMBING COMPONENTS ITEM PART NUMBER DESCRIPTION 8 8540-3 ASSEMBLY, FORMED TUBE FAUCET SUPPLY 9 86904 T UBE, FORMED ASSEMBLY 1/4FF x 1/4 FF 10 80154 FITT.
EXPLODED VIEW & PARTS LIST (continued) 22 SERVICE KITS FAUCET REPAIR KITS 82573 Handle (item 12a) 82575 Seat Cup (item 12c) 82576 Faucet Repa ir Kit (Includes 12a Handle, 12c Seat Cup, 12d Spring,.
WIRING DIA GRAM 23 605 70988 Owners Manual Integrity 5W Decanter Brewer.
PRINTED IN UNITED STATES OF AMERICA Bloo mf iel d Indu stri es, Inc . Division of Carrier Co mmercial Refrigeration In US and Can ada T elep hone: 775 -689- 5700 Fa x: 888-4 92-2783 Fa x: 800-3 56-5142 () websi te: www .
An important point after buying a device Bloomfield 8752 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bloomfield 8752 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bloomfield 8752 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bloomfield 8752 you will learn all the available features of the product, as well as information on its operation. The information that you get Bloomfield 8752 will certainly help you make a decision on the purchase.
If you already are a holder of Bloomfield 8752, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bloomfield 8752.
However, one of the most important roles played by the user manual is to help in solving problems with Bloomfield 8752. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bloomfield 8752 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
