Instruction/ maintenance manual of the product 0420 Bloomfield
Go to page of 24
BLOO MFIE LD IN D UST RIES 2 E RI K CI RCLE , P . O. B ox 2 80 V erdi, NV 894 3 9 tel eph one: 775- 689 -5 700 fax : 888- 492- 278 3 www .wel ls bl oomfi eld.
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery.
Also meets Canadian Standards MODEL STYLE FEATURES VOLTS WAT TS AMP S 1ø POWER SUPPLY CORD 0420 AUTOMATIC LO-PROFILE AIRPOT HOT WA TER DISPENSER 120 VAC 1500 NEMA 5-15P 12.5 1 TABLE OF CONTENTS SPECIFIC ATIONS Thank You for pu rchasing th is Bloomfield Industries appliance.
FE AT U R E S AN D O P E R AT I N G CO N T R OLS - AUTOMATIC BREWERS 2 Fig. 1 Features & Operating Controls for Automatic Brewers.
3 PRECAUTIONS A N D GENERAL INFORM ATION WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock.
INSTALLATION READ THIS CA R EFULL Y BEFORE ST A RTING THE INST A LL A TION Unpack the unit. Inspect all components for co m pletene ss and condition. Ensure that all packing materials have been removed from the unit. Verify that the Spray Head Gasket and Spray Disk are properly installed.
5 INSTALLATION (continued) CAUTION: ELECTRICAL DA MAGE DO NOT plug in or energi ze this appliance until all Installa tion Instructions are read an d followed. Damage to the Brewer will occur if these instructions are not followed. NOTE: W ater supply inle t line must meet certain minimum criteria to insure successful operation of the brewer.
6 WARNING: SHOCK H AZARD Brewer must be properly grounde d to pr ev en t possib le shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury. IMPORTA N T: Supply powe r m ust match nameplate for voltage and phase.
OPERATION 7 A. ST AR T-U P For initial start-up, or if the br ewer has no t been used for an extended period of time: ♦ Be sure spray disk and brew gasket are properly installed in the brew head.
Fig. 5 Program Volumes OPERATION (continued) 8 B. PROGRAM BREW VOLUMES ♦ Each BREW VOLUME SELECT KEY is individuall y programmable. ♦ Keys may be programmed for pulse brew ing to optimize contact tim es and extraction rates, or to m inimize overflowing the brew chamber when using large amounts of grounds.
OPERATION - BREWIN G COFFEE A. PREPARATION Place one (1) genuine Bloomfield paper filter in the brew chamber. Add a pre-measured amount of f resh coffee grounds. G ently shak e the bre w cham ber to level the bed of gro unds. Slide the bre w chamber into place under the brew head.
CLEANING I NSTRUCTIONS PROCEDURE: Clean Coffee Brewer PRECAUTIONS: Disconnect br e wer from electric pow er. Allow brewer to cool. FREQUENCY : Daily TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush, Bottle Brush 1. Disconnect bre w er from electric power.
TROUBLESHOOTING SUGGEST IONS SUGGESTED REMEDY Check power supp ly cord Check / reset circuit breaker Set for desired temperature Allow to cool hi-limit will self- reset Examine wiring & connectors.
SERVICING INSTRUCTIONS CAUTION: SHOCK HAZA RD Opening access pane ls o n this brew ma y expose unins ulated electrical co m ponents. Disconnect brewer from electrical power befo re removing any pan el.
SERVICING INSTRUCTIONS (continued) TEMPERATURE ADJUSTMENT Disconnect brewer from electric power. Remove top panel. Remove button plug from front panel. Pull vent tube out of tank lid and insert a thermo me ter of k now n accuracy in hole. Reconnect brewer to electrical power.
SERVICING INST RUCTIONS (continue d) 14 IMPORTANT: Before setting assembly into tank, make sure tank lid gasket is properly se ated on f lange of lid. DO NOT OVER-TIGHTEN . IMPORTANT: When mounting thermosta t , be sure to insert sensing bulb to the bottom of the bulb well.
SERVICING INSTRUCT IONS (continued) 15 REPLACE SOLENOID Symptom: Brewer will not flow water; or, brewer drips continuously from brew head. NOTE: Wrench p/n 86660 is designed to allow easy removal of f.
SERVICING IN STRUCTIONS (continued) 16 IMPORTANT: The two keyp ad ribbo n cables connectors ar e not polari ze, and can easily be installed on the wrong location on the board. Be sure to mark the ribbon cable connectors s as to location and orientation.
SERVICING INSTRUCT IONS (continued) 17 CAUTION: CHEMICAL BURN HA ZARD Deliming chemicals may be caustic. Wear appropriate protective g loves and goggle s during this procedure. Never siphon deliming chemicals or solutions by mouth. This operation should only be performed by qua lified and experienced service personnel.
0420 EXPLODED VIEW & PARTS LIST 18 CABI NE T & EL EC TRI C AL C OM PO NE N TS.
0420 EXPLODED VIEW & PART S LIST (continued) 19 PLUMBING COMPONENTS.
EXPLODED VIEW & PARTS LIST (continued) 20 SERVICE PARTS KITS 84427 VALVE ASSEMBLY, COMPLETE 85218 INLET FITTING KIT ( Includes cap, f itting, gasket & strainer) 85219 INLET STRAINER.
21 WIRING DIA GR AM.
PRINTED IN CHIN A Bloo mf iel d Indu st ri es, Inc . Division of Carrier Co m mercial Refrigeration In US and Can ada T el ep hone: 775 -6 89-5700 Fa x: 888-4 92-2783 Fa x: 800-3 56-5142 () websi te: www .
An important point after buying a device Bloomfield 0420 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bloomfield 0420 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bloomfield 0420 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bloomfield 0420 you will learn all the available features of the product, as well as information on its operation. The information that you get Bloomfield 0420 will certainly help you make a decision on the purchase.
If you already are a holder of Bloomfield 0420, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bloomfield 0420.
However, one of the most important roles played by the user manual is to help in solving problems with Bloomfield 0420. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bloomfield 0420 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
