Instruction/ maintenance manual of the product SRP-270CUG Bixolon
Go to page of 31
User ’ s Manual SRP-270 Imp act Printer Rev . 1.05 http://www .bixolon.com.
Rev . 1.05 - 2 - SRP-270 ■ T able of Content s ※ Manual Information & Usage Pr ecautions ................................................................ 3 1. Content C onfirmation ..............................................................
Rev . 1.05 - 3 - SRP-270 ■ Manual Information ※ Manual Information & Usage Precautions This user manual contains basic information for product usage as well as for emergency measures that may be required. ※ The following separate manuals provide more detailed content on various technological issues and areas.
Rev . 1.05 - 4 - SRP-270 ■ Safety Precautions In using the present appliance, please keep the following safety regul ations in order to prevent any hazard or material damage. W ARNING Violating following instructions c an cause serious injury or death.
Rev . 1.05 - 5 - SRP-270 CAUTION Violatin g following instructions c an cause sligh t wound or damage t he appliance . Do not use the printer when it is out of order . This can cause a fire or an electro cution. • Switch off and unplug the printer before calling your dealer .
Rev . 1.05 - 6 - SRP-270 ■ Other Precautions The copyright for this user manual and various other manuals is pr operty of the BIXOLON Co., Ltd. Any copying or conversion into electronic firm and saving of this material without the express written permi ssion of BIXOLON Co.
Rev . 1.05 - 7 - SRP-270 1. Content Confirmation The following items should all be c ontained in the printer p ackage. Contact the dealer from which the purchas e was made if any it em is damaged and/or missing.
Rev . 1.05 - 8 - SRP-270 2. Product Part Names Cartridge Knob Printer Cover S pool Ribbon Cartridge Auto Cutter Paper Feed Button Power Switch.
Rev . 1.05 - 9 - SRP-270 3. Installation & Usage 3-1 Power Connection Connect power to the prin ter as shown below . 1) T urn off the printer power switch. 2) Check to see that the AC adapter voltage matches that of the power source. 3) Connect the AC adapter jack to the printer power connector .
Rev . 1.05 - 10 - SRP-270 3-2 Interface Cable Connection Connect the printer with a POS system (PC, E CR, etc.) via an interface cable as shown below .
Rev . 1.05 - 1 1 - SRP-270 3-3 Cash Drawer Connection Connect the printer and cash drawer via the interface cable as shown below . 1) T urn off the power switch on both the printer and the POS system (PC, ECR, etc.). 2) Connect the cash drawer cable to the printer cash drawer connector .
Rev . 1.05 - 12 - SRP-270 3-4 Ribbon Cartridge Installation Install the ribbon cartridge as shown below . 1) T urn off the printer power switch. 2) Open the printer cover . 3) Before inserting the ribbon cartridge, turn the cartridge knob clockw ise in order prevent the ribbon from tangling.
Rev . 1.05 - 13 - SRP-270 3-5 Paper Installation The paper used varies by printer model. - SRP-270 A/C: 1-layer paper - SRP-270 D: 2-layer paper 3-5-1 SRP-270 A/C Model 1) T urn on the printer power . 2) Open the printer cover . (Remove any core of a fully used paper roll if present.
Rev . 1.05 - 14 - SRP-270 5) Insert the end of t he paper roll into the p aper slot as shown below . The paper then feeds automatically . Automatic cutting is available for printer models equipped with auto cutters. (SRP-270C) - For printer models without auto cutters, tear of f the paper as shown below .
Rev . 1.05 - 15 - SRP-270 3-5-2 SRP-270 D Model 1) T urn on the printer power . 2) Open the printer cover . (Remove any core of a fully used paper roll if present.) 3) Undo the paper roll, and make sure that the lower edge is cleanly cut. 4) Insert the paper roll as s hown below .
Rev . 1.05 - 16 - SRP-270 5) Insert the end of t he paper roll into the p aper slot as shown below . The paper then feeds automatically . 6) T urn the spool and insert the p aper into the groove. Wrap the p aper around the spool several times, and then affix into the spool slot.
Rev . 1.05 - 17 - SRP-270 7) T ear of f any extruding paper . 8) Close the auto cutter , and then close the printer cover . ( C o r r e c t P a p e r I n s t a l l a t i o n ) ( I n c o r r e c t P a .
Rev . 1.05 - 18 - SRP-270 3-6 Control Panel Usage O Feed Press this button to feed paper . This button is also used for self-tests and hexa-printing. - Refer to “4. Self-Test” for details related to self-tests. - Refer to the service manual for information on hexa-printing.
Rev . 1.05 - 19 - SRP-270 4. Self-Test Run the self-test when first setting the prin ter or when encountering a problem. The following printer attributes can be assessed.
Rev . 1.05 - 20 - SRP-270 5. Fine Tuning 5-1 Dip Switch Adjustment The dip switches can be used to select the following printer functions. - Emulation - Auto Cutter, Font In terval, Auto Line Feed - Serial Communications Settings, Hexa-Printing The dip switches are located on the under side of the printer.
Rev . 1.05 - 21 - SRP-270 [Diagram 1] Switch Functions When Us ing a Serial Interface (RS232C & RS485) [Dip Switch 1 Settings] Switch Function On Off Default SW1-1 Off SW1-2 Emulation Selection Refe r to Chart (1) below .
Rev . 1.05 - 22 - SRP-270 [Diagram 2] Switch Functions When Using a Parallel or USB Interface [Dip Switch 1 Settings] Switch Function On Off Default SW1-1 Off SW1-2 Emulation Selection Refe r to Chart (1) below .
Rev . 1.05 - 23 - SRP-270 5-2 Paper Jam Removal Remove jammed paper as shown below . 1) Open the printer cover . 2) Lift the lock mechanism handle and raise the auto cutter . 3) Remove the ribbon cartridge. 4) Use a screwdriver or coin to l oosen the manual screw as shown above.
Rev . 1.05 - 24 - SRP-270 6) Push the head to the left and fix in place. 7) T urn the paper feed knob and remove the jammed p aper . 8) Replace the head cover and fasten the screw . 9) Place the ribbon cartridge and paper back in their original positions and close the printer cover .
Rev . 1.05 - 25 - SRP-270 ※ CAUTION If the cutting edge of the auto cutter is not in it s normal posit ion, p aper cannot be inserted properly . Insert a screwdriver into the hole near the bottom of the auto cutter as shown below , and turn the gear within the auto cutter to adj ust the cutting edge to its normal position.
Rev . 1.05 - 26 - SRP-270 6. Appendix 6-1 Specifications Item Description Printing Method Serial Imp a ct Dot Head Pin Number 9 Print Direction T wo-way Print S peed 4.
Rev . 1.05 - 27 - SRP-270 6-2 RS-232C (Serial Interf ace) Cable Specifications 1) Printer Rear Image ※ Turning the dip switch on the Serial inte rface to the ON position connects DTR and R TS signals together . 2) Cable S pecifications (Shield.G) (S.
Rev . 1.05 - 28 - SRP-270 6-3 RS-485 (Serial Interf ace) Cable Specifications 1) Printer Rear Image 2) Cable S pecifications Pin No. Signal Direction Function 1 FGND - Frame Ground 2 SD2 Output Send D.
Rev . 1.05 - 29 - SRP-270 6-4 IEEE1284 (Parallel Interf ace) Cable Specifications 1) Printer Rear Image 2) Cable S pecifications Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe .
Rev . 1.05 - 30 - SRP-270 6-5 USB Interface Cable Specifications 1) Printer Rear Image 2) Cable S pecifications Pin No. Signal Wire Color Function 1 VBUS Red Host Power 2 D- White Data (D-) 3 D+ Green Data (D+) 4 GND Black Signal Ground Shell Shield Drain Wire Frame Ground 6-6 Cash Drawer Cable Specifications Pin No.
Rev . 1.05 - 31 - SRP-270 6-7 Certification 1) EMC & Safety S tandards • Europe: CE EMC,CB-Scheme:IE C60950-1, GS: EN60950-1: 2001 • North America: FCC rules parts 15B WARNING Use of an unprotected interface cable with th is printer conflicts with EMC st andards.
An important point after buying a device Bixolon SRP-270CUG (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bixolon SRP-270CUG yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bixolon SRP-270CUG - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bixolon SRP-270CUG you will learn all the available features of the product, as well as information on its operation. The information that you get Bixolon SRP-270CUG will certainly help you make a decision on the purchase.
If you already are a holder of Bixolon SRP-270CUG, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bixolon SRP-270CUG.
However, one of the most important roles played by the user manual is to help in solving problems with Bixolon SRP-270CUG. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bixolon SRP-270CUG along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
