Instruction/ maintenance manual of the product ZRM-E36AS Zephyr
Go to page of 19
Use, Care, and Installation Guide www .zephyronline.com Model number: Serial Number: SEP07.0101 © Zephyr Corporation Roma Island ZRM-E36AS ZRM-E42AS.
www .zephyronline.com.
1 SAFETY NOTICE ................................................................. 2-3 LIST OF MA TERIALS ....................................................... 4 INST ALLA TION Ducting Calculation Sheet ....................................... 5 Mounting Height & Clearance .
Important Safety Notice READ AND SA VE THESE INSTRUCTIONS 2 www .zephyronline.com W ARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS F AN WITH ANY SOLID-ST A TE CONTROL DEVICE. W ARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSER VE THE FOLLOWING: a.
Important Safety Notice 3 W ARNING TO REDUCE THE RISK OF FIRE, USE ONL Y MET AL DUCTWORK. CAUTION 7 RUHGXFHULVNRI¿UHDQGWRSURSHUOH[KDXVWDLURXWVLGH'RQRWYHQWH[KDXVWDLULQWRVSDFHVZLWKLQZDOOVFHLOLQJV attics, crawl spaces or garages.
List of Materials 4 www .zephyronline.com MODEL: ZRM-E36AS, ZRM-E42AS 2 Top Duct Covers 1 Top Support Frame 2 Bottom Duct Covers 1 Bottom Support Frame 2 Thin Trim Pieces 2 Thick Trim Pieces 1 Hood 4 Halogen Light Bulbs (pre-installed) 2 Metal Filters ( 3 - ZRM-E42AS) 3 Wire Nuts 4 ø14 OD / ø6.
5 Duct pieces To t a l Equivalent number length x used = 3-1/ 4” x 10” Rect., straight 1 F t. x ( ) = Ft. 8” Round, straight 1 F t. x ( ) = Ft. 3-1/ 4” x 10” Rect. 9 0 0 elb ow 15 F t. x ( ) = Ft. 3-1/ 4” x 10” Rect. 45 0 elb ow 9 F t. x ( ) = Ft.
Installation – Mounting Height & Clearance 6 www .zephyronline.com DUCTING A minimum of 6” round or 3-1/4 x 10” rectangular GXFWPXVWEHXVHGWRPDLQWDLQPD[LPXPDLUÀRZ HI¿FLHQF Always use rigid type metal ducts only .
7 W ARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only .
8 www .zephyronline.com Installation – +RRG6SHFL¿FDWLRQV 3/4” 7 1/8 ” 10 3/4 ” 7 7/8 ” 10 1/8 ” 12 3/8 ” 8 3/4 ” FRONT 36” or 42” 27” 12” 14” 4” T op Support Frame (cei.
9 $GGDQGVHFXUHZRRGEORFNLQJ minimum 2 x 4 RQWRFHLOLQJMRLVWV 2. Fasten top support frame to desired location on ceiling using 4 2” wood screws with washers. The wider section of the support bracket faces the front of the hood.
10 www .zephyronline.com 7 8 10 9 11 Top Duct Covers Top Support Frame Bottom Duct Covers Bottom Support Frame Thin Trim Piece Thick Trim Piece $VVHPEOHWRSGXFWFRYHUV With louv.
11 Ductless recirculating is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood.
12 www .zephyronline.com Blower Off Lights On/Off Blower On/Speed Selection Blower Off Blower On/Speed Selection Lights On/Off The blower will be switched off by pressing: Switch blower on and select .
13 SURF ACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel wool/scouring pads which will scratch and damage surface.
14 www .zephyronline.com REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. T ouching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot.
T roubleshooting 15 TROUBLESHOOTING PROCEDURES FOR ROMA Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting properly .
16 www .zephyronline.com DESCRIPTION P ART# Replacement Parts /LJKW%XOE05*8:HDFK =%6 0HWDO)LOWHUHDFK .
1-888-880-8368 STAPLE YOUR RECEIPT HERE TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: Zephyr Corporation (referred to herein as “we” or “us”) warrants to .
An important point after buying a device Zephyr ZRM-E36AS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zephyr ZRM-E36AS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zephyr ZRM-E36AS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zephyr ZRM-E36AS you will learn all the available features of the product, as well as information on its operation. The information that you get Zephyr ZRM-E36AS will certainly help you make a decision on the purchase.
If you already are a holder of Zephyr ZRM-E36AS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zephyr ZRM-E36AS.
However, one of the most important roles played by the user manual is to help in solving problems with Zephyr ZRM-E36AS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zephyr ZRM-E36AS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
