Instruction/ maintenance manual of the product ZNA-M90S Zephyr
Go to page of 21
Use, Care, and Installation Guide www .zephyronline.com Model number: Serial Number: MAR09.0102 © Zephyr Corporation Napoli Island ZNA-M90S ZNA-E42S.
www .zephyronline.com.
1 SAFETY NOTICE ................................................................. 2-3 LIST OF MA TERIALS ....................................................... 4 INST ALLA TION Ducting Calculation Sheet ....................................... 5 Mounting Height & Clearance .
Important Safety Notice READ AND SA VE THESE INSTRUCTIONS 2 www .zephyronline.com W ARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS F AN WITH ANY SOLID-ST A TE CONTROL DEVICE. W ARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSER VE THE FOLLOWING: a.
Important Safety Notice 3 W ARNING TO REDUCE THE RISK OF FIRE, USE ONL Y MET AL DUCTWORK. CAUTION T o reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages.
List of Materials 4 www .zephyronline.com (3) Wire Nuts (1) Suction Cup (4) ø12 OD / ø5 ID W ashers (4) M4 x 1-1/2” Wood Screws (2) M4 x 8 Philips Head Screws 1 - Hardware package 1 - Top support .
5 Duct pieces To t a l Equivalent number length x used = 3- 1/ 4” x 10” Rect., straight 1 Ft. x ( ) = Ft. 8” Round, straight 1 Ft. x ( ) = Ft. 3- 1/ 4” x 10” Rect. 90 0 elb ow 15 Ft. x ( ) = Ft. 3- 1/ 4” x 10” Rect. 45 0 elb ow 9 Ft. x ( ) = Ft.
Installation – Mounting Height & Clearance 6 www .zephyronline.com DUCTING A minimum of 6” round ducting must be used to maintain maximum air fl ow ef fi ciency . Always use rigid type metal ducts only . Flexible ducts could restrict air fl ow by up to 50%.
7 W ARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only .
8 www .zephyronline.com Installation – Hood Speci fi cations 35 7 16 " /42"[1065] 900 Min 32 1 2 " 826 Max 49"[1244] 11 13 16 " 300 25 9 16 " 650 1 9 16 " 40 9 13.
9 Add Blockings Fasten Support Frame Install Duct Cover Fasten upper duct cover Adjust height & fasten frame 1. Add and secure blocking (minimum 2x4 studs onto ceiling joists. 2. Fasten mounting telescopic support frame directly onto ceiling joist or stud blockings.
10 www .zephyronline.com Mount hood onto support frame 6. Lift lower duct cover and hood body onto bottom of support frame. 7. Secure hood body to bottom support with (4) screws. Access the screws from inside the hood. This will require at least two people.
11 Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and fi ltered by a set of optional charcoal fi lters.
12 www .zephyronline.com Lights On/Dim/Off 15 Min Delay Off Display (speed level, delay off, filter clean/change) Adjust 6 Speed Levels Blower On/Off 1. Blower On/Off By pressing the blower is switched on and off. When switched on, the blower starts up on speed level 3.
Features & Controls – Charcoal Filter Change Reminder 13 Charcoal Filter Change Reminder (charcoal filter , if installed) When your hood is installed as a recirculating unit, it is fitted with a set of charcoal filters to purify exhaust and fumes from cooking, then re-circulates the air within the home.
Features & Controls – Metal Mesh Filter Clean Reminder 14 www .zephyronline.com Metal Filter Clean Reminder (metal mesh filter) Whether your hood is installed as an exhaust or purifying unit, a set if metal mesh filters are fitted by the factory , These metal mesh filters are intended to filter out residue from cooking.
15 SURF ACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel wool/scouring pads which will scratch and damage surface.
16 www .zephyronline.com REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. T ouching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot.
T roubleshooting 17 TROUBLESHOOTING PROCEDURES FOR NAPOLI ISLAND Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting properly .
18 www .zephyronline.com DESCRIPTION P ART# Replacement Parts Light Bulb GU10 50W (each) Z0B-0020 Metal Filter (each) 50200004 Optional Accessories Recirculating Kit ZRC-0060 Replacement Charcoal Filter (each) Z0F-C002 Duct Cover Extension Z1C-00NA T o order parts, visit us online at http://store.
1-888-880-8368 STAPLE YOUR RECEIPT HERE TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: Zephyr Corporation (referred to herein as “we” or “us”) warrants to .
An important point after buying a device Zephyr ZNA-M90S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zephyr ZNA-M90S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zephyr ZNA-M90S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zephyr ZNA-M90S you will learn all the available features of the product, as well as information on its operation. The information that you get Zephyr ZNA-M90S will certainly help you make a decision on the purchase.
If you already are a holder of Zephyr ZNA-M90S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zephyr ZNA-M90S.
However, one of the most important roles played by the user manual is to help in solving problems with Zephyr ZNA-M90S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zephyr ZNA-M90S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
