Instruction/ maintenance manual of the product AK7548ASX Zephyr
Go to page of 22
Use, Care, and Installation Guide www .zephyronline.com Model number: Serial Number: Date of Purchase: Sales Dealer: JAN08.0201 © Zephyr Corporation T empest II AK7500ASX AK7536ASX AK7548ASX READ AND.
www .zephyronline.com.
1 SAFETY NOTICE ................................................................. 2-3 LIST OF MA TERIALS ....................................................... 4 INST ALLA TION Ducting Calculation Sheet ....................................... 5 Mounting Height & Clearance .
Important Safety Notice READ AND SA VE THESE INSTRUCTIONS 2 www .zephyronline.com W ARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS F AN WITH ANY SOLID-ST A TE CONTROL DEVICE. W ARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSER VE THE FOLLOWING: a.
Important Safety Notice 3 W ARNING TO REDUCE THE RISK OF FIRE, USE ONL Y MET AL DUCTWORK. CAUTION T o reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages.
List of Materials 4 www .zephyronline.com MODELS: AK7500ASX, AK7536ASX, AK7548ASX P ARTS SUPPLIED 1 - Hood 2 - Baffl e fi lters AK7500ASX, 3 - AK7536ASX, 4 - AK7548ASX 2 - Halogen light bulbs 3 - AK.
5 Installation – Ducting Calculation Sheet Duct pieces To t a l Equivalent number length x used = 3-1/ 4” x 10” Rect., straight 1 Ft . x ( ) = Ft. 7”-10” Round, straight 1 Ft . x ( ) = Ft. 3-1/ 4” x 10” Rect. 9 0 0 elb ow 15 Ft . x ( ) = Ft.
Installation – Mounting Height & Clearance 6 www .zephyronline.com DUCTING A minimum of 6” round or 3-1/4” x 10” rectangular duct must be used to maintain maximum air fl ow effi ciency for single blower and 10” round duct for dual and external blower .
7 W ARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only . Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver T ape or Duct T ape.
8 www .zephyronline.com Installation – Specifi cations 29 15/16 ” (30”) 35 15/16 ” (36”) 47 15/16 ” (48”) 24” (30”) 30” (36”) 42” (48”) 12” *10 ” 24” 4” 18” 1 3/8 .
9 ELECTRICAL W ARNING All Electrical work must by performed by qualifi ed electrician or person with similar technical know how and background. For personal safety , remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance.
10 www .zephyronline.com C/L C/L A B 12 3/8 ” min 26” 4” wood board fig. 2 fig. 1 C D E fig. 2 - C fig. 2 - E fig. 2 - D NUT SCREW Installation – Mounting the Range Hood 1. Measure distance from range top to hood bottom ( 26” min ) Level and mark line A.
11 PBI-1 100A DUAL INTERNAL BLOWER WILL ACCOMODA TE VERTICAL DUCTING ONL Y Please turn to page 12 for instructions on installing CBI-600B in horizontal ducting mode. 1. Position blower plate over bracket on inside back of hood and pivot up. Secure plate to hood with (2) 10x3/16” screws.
12 www .zephyronline.com HORIZONT AL DUCTING IS ONL Y A V AILABLE IF USING THE CBI-600B SINGLE INTERNAL BLOWER. 1. Unscrew (4) screws holding blower to plate and remove blower . 2. Cover round blower opening on blower plate with 6” round metal cap included with the CBI-600B.
13 Installation – CBI-600B Horizontal Ducting Conversion 6. Attach 6” round to rectangular transition adapter to hood with (4) M4x8 screws. 7. Attach blower brackets to blower with (4) 10x3/16” screws. (2) screws for each bracket. 8. Place blower into round end of 6” round transition adapter .
14 www .zephyronline.com Installation – External Blower Preparation 1. Place 10” round adapter on top of hood and secure with (4) M4x8 screws. Connect 10” round duct work to 10” round adapter . 2. Install threaded end of external blower wiring through external blower wiring knock out located inside the hood.
15 Blower On/Off By pressing , the blower is switched On and Off. When switched on, the blower turns on at the same speed it was switched off at. When switched off the entire hood powers off, including the lights. Speed Selection The 3 speed levels are selected by pressing to decrease and to increase speed level.
16 www .zephyronline.com SURF ACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners.
17 REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. T ouching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise.
T roubleshooting 18 www .zephyronline.com TROUBLESHOOTING PROCEDURES FOR TEMPEST I AND TEMPEST II Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON.
19 DESCRIPTION P ART # Replacement Parts Light Bulb MR16 (GU10) 35W (each) Z0B-0023 Baffl e Filter (each) 50210004 Optional Accessories Single Internal Blower CBI-600B Dual Internal Blower PBI-1 100A.
1-888-880-8368 STAPLE YOUR RECEIPT HERE TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: Zephyr Corporation (referred to herein as “we” or “us”) warrants to .
An important point after buying a device Zephyr AK7548ASX (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zephyr AK7548ASX yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zephyr AK7548ASX - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zephyr AK7548ASX you will learn all the available features of the product, as well as information on its operation. The information that you get Zephyr AK7548ASX will certainly help you make a decision on the purchase.
If you already are a holder of Zephyr AK7548ASX, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zephyr AK7548ASX.
However, one of the most important roles played by the user manual is to help in solving problems with Zephyr AK7548ASX. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zephyr AK7548ASX along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
