Instruction/ maintenance manual of the product G2000T Zenoah
Go to page of 16
G2000T GB-1 G B G2000T CHAIN SA W OWNER’S MANUAL G B 848C0593A0 (704).
G2000T GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 8 3. Installing Guide Bar and Saw Chain .
G2000T GB-3 G B 1. For safe operation W ARNING This chainsaw has been especially designed for tree maintenance and should therefor e only be used by trained operators when working on trees.
G2000T GB-4 20. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dan- gerous carbon monoxide. 21. Do not operate the chain saw in a tree unless specially trained to do so.
G2000T GB-5 G B W ORKING WITH TREE SERVICE CHAIN-SA WS FROM A R OPE AND HARNESS This chapter sets out working practices to reduce the risk of injury from tree service chainsaws when working at height from a r ope and harness.
G2000T GB-6 Gaining a good footing at the working position can be assisted by use of a temporary foot stirrup created from an endless sling. Starting the saw in the tree When starting the saw in the t.
G2000T GB-7 G B 2. Explanation of Symbols on the Machine The port to refuel “MIX GASOLINE” Position: Fuel cap The port to top up chain oil Position: Oil cap Setting the switch to the “O” position, the engine stops immediately . P osition: Front at the top of the rear handle Starting the engine.
G2000T GB-8 Open the box and install the guide bar and the saw chain on the power unit as follows: The saw chain has very sharp edges. Use thick pro- tective gloves for safety . 1. Pull the guard towar ds the fr ont handle to check that the chain brake is not engaged.
G2000T GB-9 G B 4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate de- pending on oil ingredients, sufficient agitation is nec- essary for the engine to last long.
G2000T GB-10 6. When engine has ignited, first turn in the choke knob to the first-stage position (2) and then pull the starter again to start the engine. 7. Allow the engine to warm up with the throttle lever pulled slightly . Keep clear of the saw chain as it will start rotating upon starting of engine.
G2000T GB-11 G B • When the brake operates, release the thr ottle lever to slow down the engine speed. Continuous opera- tion with the brake engaged will generate heat from the clutch and may cause trouble. • At machine inspection prior to each job, check the operating condition of the brake following the steps.
G2000T GB-12 ■ FELLING A TREE 1. Decide the felling direction considering the wind, lean of the tree, location of heavy branches, ease of completing the task after felling and other factors. 2. While clearing the area ar ound the tr ee, arrange a good foothold and retr eat path.
G2000T GB-13 G B 3. Oil filter 1. With a wire hook, take out the oil filter fr om the feed- ing port. 2. W ash the filter with gasoline. When returning the filter , use a pinch and make sure that the pipe is not folded and the filter is placed at the bottom of the tank as shown in the picture.
G2000T GB-14 ■ SA W CHAIN It is very impor tant for smooth and safe operation to always keep the cutters sharp. The cutters need to be sharpened when: • Sawdust becomes powder -like. •Y ou need extra force to saw in. • The cut path does not go straight.
G2000T GB-15 G B 9. T r oubleshooting Guide Case 1. Starting failure Make sure the icing pr evention system is not working. Check fuel for water or substandard mix- ture. Replace with proper fuel. Check for engine flooding. Check spark ignition. Remove and dry the spark plug.
G2000T GB-16 Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer .
An important point after buying a device Zenoah G2000T (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zenoah G2000T yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zenoah G2000T - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zenoah G2000T you will learn all the available features of the product, as well as information on its operation. The information that you get Zenoah G2000T will certainly help you make a decision on the purchase.
If you already are a holder of Zenoah G2000T, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zenoah G2000T.
However, one of the most important roles played by the user manual is to help in solving problems with Zenoah G2000T. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zenoah G2000T along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
