Instruction/ maintenance manual of the product ZWI 1125 Zanussi
Go to page of 28
EN User manual Washing Machine ZWI 1125.
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Washing Programmes _ _.
• If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance. • Always be sure, that there is no water leakage from ho- ses and their connections after the installation.
Product description 1 Detergent dispenser drawer 2 Control panel 3 Door opening handle 4 Rating plate 5 Drain pump 6 Adju stable f eet 1 2 3 4 5 6 Detergent dispenser drawer Compartment for detergent used for prewash and soak phase or for stain remover used during the stain action phase (if available).
1 2 3 4 5 6 B C A 7 1 Programme selector dial 2 SPIN reduction button 3 OPTIONS button 4 EXTRA RINSE button 5 START/PAUSE button 6 DELAY START button 7 Indicator pilot lights Table of symbols Push but.
Start Pause This button allows you to start or to interrupt the selected programme. Delay Start The start of the programme can be delayed by 3, 6 or 9 hours by means of this button. Indicator pilot light (7) B C A When selecting a washing programme both lights A and B illuminate.
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Options Detergent Compartment COTTONS 60° - 40° - 30° - Cold Main wash - Rinses Maximum spin speed at 1200 rpm Max. load 6 kg - Reduced load 3 kg 1) Whit e and colo ured cot ton (normally soiled items).
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Options Detergent Comp artment WOOL/HANDWASH 30° - C old Main wash - Rinses Maximum spin speed at 900 rpm Max. load 2 kg Washing programme for machine washable wool as well as for hand washable woollens and delicate fabrics.
Before loading the laundry Never wash whites and coloureds together. Whites may lose their whiteness in the wash. New coloured items may run in the first wash; they should therefore be washed separately the first time. Button up pillowcases, close zip fasteners, hooks and poppers.
When the degree of hardness is soft, readjust the quantity of the detergent. First use • Ensure that the electrical and water connections comply with the installation instructions.
When selecting a programme, the light corresponding to the maximum speed allowed for that programme will illu- minate. Select the available opti ons b y pressing buttons 3 and 4 Depending on the programme, different functions can be combined. These must be selected after choosing the de- sired programme and before starting the programme.
continues to run at regular intervals until the water drain- ing. Follow the below instructions to empty out the water: 1. Turn the programme selector dial to . 2. Set the draining or spinning programme. 3. If needed, reduce the spin speed, . 4. Press button 5 .
Place a container close to the pump ( A ) to collect any spillage. Pull out the emergency emptying hose ( B ), place it in the container and re- move its cap. When no more water comes out, unscrew the pump cover by turning it anti-clockwise and remove the filter.
Frost precaution If the machine is exposed to temperatures below 0°C, cer- tain precautions should be taken. • Turn off the water tap. • Unscrew the inlet hose. • Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out.
Problem Possible cause/Solution The washing machine does not start: The door has not been closed (the button 5 red light blinks). • Close the door firmly. The plug is not properly inserted in the power socket. • Insert the plug into the power socket.
Problem Possible cause/Solution There is water on the floor: Too much detergent or unsuitable detergent (creates too much foam) has been used. • Reduce the detergent quantity or use another one. Check whether there are any leaks from one of the inlet hose fittings.
Problem Possible cause/Solution Spinning starts late or the machine does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rota- tion of the drum.
Consumption values Programme Energy consumption (KWh) 1) Water consumption (litre) 1) Programme duration (Minutes) 1) White Cottons 90 °C 2.0 61 140 Cottons 60 °C 1.35 58 125 Cottons 40 °C 0.75 58 120 Synthetics 40 °C 0.9 50 90 Delicates 40 °C 0.
Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units. Level the washing ma- chine by raising or lower- ing the feet.
1. Into a drainage standpipe. Firstly form a hook in the end of the drain hose using the “U” piece” supplied. “U” piece supplied Place the drain hose into your standpipe, which should have an internal diameter of approximately 38 mm thus ensuring there is an air break between the drain hose and standpipe.
SHOWER WASHING MACHINE DISHWASHER BA TH SINK TOILET BIDET RAINWA TER ‘RUN-OFF’ SURF ACE WA TER DRAINS & SEWERS UNTREA TED DISCHARGE RIVER RIVER TREA TED DISCHARGE FOUL DRAIN FOUL SEWERS SEWAGE.
A 600 596 555 170 75 176,5 416 100 60 818 min. 820 min. 560 When installing the appliance into the kitchen furniture ensure, if possible, the hoses are placed in either of the two recesses on the back of the appliance. This will help to prevent the hoses from becoming kinked or trapped.
D 4 6 8 Caution! Do not remove the screw 8 ! d) Counter-magnet (6) The appliance is prearranged for a magnetic closure of the door. To enable a correct operation of this device, it is neces- sary to screw the counter-magnet (6) (steel disk + rub- ber ring) into the inner side of the door.
Drill four fixing holes see Fig. G Position the base into the recess with its front edge as far forward as the adjoining plinth line will allow. The reason for placing the base in this position is to al- low a small strip of beading to be fitted in front of the appliance feet.
25.
26.
27.
www.zanussi.com/shop 132966891-A-462011.
An important point after buying a device Zanussi ZWI 1125 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zanussi ZWI 1125 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zanussi ZWI 1125 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zanussi ZWI 1125 you will learn all the available features of the product, as well as information on its operation. The information that you get Zanussi ZWI 1125 will certainly help you make a decision on the purchase.
If you already are a holder of Zanussi ZWI 1125, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zanussi ZWI 1125.
However, one of the most important roles played by the user manual is to help in solving problems with Zanussi ZWI 1125. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zanussi ZWI 1125 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
