Instruction/ maintenance manual of the product ZGP 982 Zanussi
Go to page of 16
INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB GAS HOB ZGP 982.
2 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low Vo ltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 .
3 Content s For the User For the Inst aller Import ant Safety Information 2 Description of the Hob 3 Operation 4 Maintenance and Cleaning 4 Something Not Working? 5 Service and S pare Parts 5 Guarante.
4 Operation Hob burners To light a burner: l push in the relevant control knob and turn it to maximum position. l Upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (Fig. 1 letter C) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted.
5 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
6 Zanussi Guarantee conditions W e, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of.
7 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY Guernsey Electricity PO Box 4 V ale, Guernsey Channel Islands JERSEY Jers.
8 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 MIDLANDS BIRMINGHAM 66 Birch Road East (M18) Wyrley Road Ind. Est ate Witton Birmingham B6 6DB BOURNE Manning Road Ind. Estate (M44) Pinfold Road Bourne PE10 9HT BRIDGNOR T H 68 St.
9 BURNER RAPID SEMI-RAPID AUXILIARY (large) (m edium) ( small) POSITION M A X MI N M A X M IN M A X MI N M A X MI N NOMINAL THERMAL POW ER k W 3 . 0 0.65 2.0 0.45 1.0 0.33 3.5 1.2 NOMINAL FLOW RATE m 3 /h 0.286 0.062 0.190 0.043 0.095 0.031 0.333 0.114 NOZZLE REFERENCE 1 1 9 A d j u s t .
10 FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 mm 400 mm 400 mm 100 mm 20 mm 900 mm 700 mm 400 mm 400 mm 100 mm 20 mm 900 mm FO 2540 FO 2541 Import ant safety requirement s This hob must be inst alled in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition).
11 Carry out the installation of the hob as follows (follow also the instructions given on the Assembly and cut outlines supplied with the appliance): 1 ) measure the worktop for the exact posit.
12 A) End of shaft with nut B) W asher C) Elbow FO 0814 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper . Connection to the gas supply can be carried out on the le ft or on the right of the hob connection pipe.
13 A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 5 6 220/240 A Wiring Diagram Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary .
14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check .
15 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
CUST OMER CARE Zanussi 55-77 High S treet Slough Berkshire, SL1 1DZ T el: 08705 727727 © Electrolux Household Appliances Limited 2000 Grafiche MDM - Forlì 35683-4501 09 /00 From the Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use.
An important point after buying a device Zanussi ZGP 982 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zanussi ZGP 982 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zanussi ZGP 982 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zanussi ZGP 982 you will learn all the available features of the product, as well as information on its operation. The information that you get Zanussi ZGP 982 will certainly help you make a decision on the purchase.
If you already are a holder of Zanussi ZGP 982, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zanussi ZGP 982.
However, one of the most important roles played by the user manual is to help in solving problems with Zanussi ZGP 982. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zanussi ZGP 982 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
