Instruction/ maintenance manual of the product ZGG 782 Zanussi
Go to page of 20
GAS HOBS ZGG 642 ZGG 782 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB.
2 Import ant Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Inst allation z .
3 Content s For the User For the Inst aller Important Safety Information 2 Description of the Hob 4 Operation 5 Maintenance and Cleaning 6 Something Not Working? 7 Service and S pare Part s 7 Guarante.
4 Description of the Hob 1 1 2 3 4 2 1 3 1 1 4 ZGG 642 ZGG 782 1. Semi-rapid Burners 2. Rapid Burner 3. Auxiliary Burner 4. Control knobs 1. Semi-rapid Burners 2.
5 Operation Hob burners To light a burner: z push in the relevant control and turn it to maximum position; z then adjust the flame as required. z If the burner does not ignite, turn the control knob to zero, and try again.
6 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
7 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or inst allation, a charge will be made even if the appliance is under guarantee.
8 OVERALL DIMENSIONS ZGG 642 ZGG 782 Width: 580 mm. 680 mm. Depth: 510 mm. 510 mm. CUT OUT DIMENSIONS ZGG 642 ZGG 782 Width: 550 mm. 560 mm. Depth: 470 mm.
9 Import ant safety requirement s This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.
10 Cut Out Size The dimensions of the cut-out are given in the diagram. 550 4 7 0 30 Rectangular cut-out size for hob Dimensions are given in mm. FO 2038 FO 2098 ZGG 642 ZGG 782 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 Inst allation IMPORTANT This hob must be installed by a competent person to the relevant Gas Standards.
11 Building In ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 Dimensions are given in mm. FO 1013 3 Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface.
12 ) Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
13 A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 5 6 220/240 A W iring Diagram Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary .
14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check .
15 Commissioning When the hob has been fully inst alled it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - Turn the gas t ap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
16 Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof.
17 This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law.
18.
19.
Grafiche MDM - Forlì 35668-9204 1 1/06 www .zanussi-electrolux.co.uk.
An important point after buying a device Zanussi ZGG 782 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zanussi ZGG 782 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zanussi ZGG 782 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zanussi ZGG 782 you will learn all the available features of the product, as well as information on its operation. The information that you get Zanussi ZGG 782 will certainly help you make a decision on the purchase.
If you already are a holder of Zanussi ZGG 782, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zanussi ZGG 782.
However, one of the most important roles played by the user manual is to help in solving problems with Zanussi ZGG 782. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zanussi ZGG 782 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
