Instruction/ maintenance manual of the product 109T Yard-Man
Go to page of 18
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 20” Mulching Self Starter Push Mower Model 109T Warning: This unit is equipped wi.
2 TABLE OF CONTENTS Content Page Important Safe Operation Practices ................................................................... 3 Slope Gauge .....................................................................................................
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine.
4 20. Never operate mower without proper trail shield, discharge cover, grass catcher, blade control handle or other safety protective devices in place and working. Never operate mower with damaged safety devices. Failure to do so, can result in personal injury.
5 meet the original equipment specifications may lead to improper performance and compromise safety!” 4. Mower blades are sharp and can cut. Wrap the blade or wear gloves, and use extra caution when servicing them. 5. Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition.
6 SECTION 2: SLOPE GAUGE Use this page as a guide to determine slopes where you may not operate the lawn mower safely. 15 ° S I G H T A ND H O L D T H I S L EVE L W I T H A VE R T I C A L T R EE A P .
7 SECTION 3: UNPACKING Removing Unit From Carton • Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton. • Remove loose parts if included with unit (i.e., operators manual, bottle of oil, etc.).
8 • The rope guide is attached to the right side of the upper handle. Loosen the wing nut which secures the rope guide. For location of the wing nut, see Figure 4. Figure 4 • With the spark plug wire disconnected and grounded, and with the safety key in the locked position, pull the starter rope out of the engine.
9 NOTE: The safety key must be in the run position to start the mower for both systems, either the self starter or recoil starter. Start Control Button The start control button is located on the upper left side of the handle.
10 1. Check oil level and add fuel, if necessary. 2. Open shut off valve (if equipped) 1/4 turn. 3. Turn safety key 1/4 turn clockwise to RUN position. 4. Firmly push primer bulb 3 times (For a cold engine only!). 5. While standing at upper handle, depress the starter control button with the thumb of your right hand.
11 SECTION 7: MAKING ADJUSTMENTS WARNING: Be sure to disconnect the spark plug wire and DE-ENERGIZE starter before performing any adjustments or repairs. DO NOT attempt any maintenance or service to the engine and/or mower equipped with the safety key in the unlocked and/or energized mode.
12 SECTION 8: SERVICE WARNING: Be sure to disconnect the spark plug wire and DE-ENERGIZE starter before lubricating, repairing or servicing. DO NOT attempt any maintenance or service to the engine and/or mower equipped with the safety key in the unlocked and/or energized mode.
13 Figure 11 WARNING: Periodically inspect the blade adapter for cracks, especially if you strike a foreign object. Replace when necessary. • When sharpening the blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade.
14 SECTION 10: OFF-SEASON STORAGE The following steps should be taken to prepare lawn mower for storage. WARNING: Be sure to disconnect the spark plug wire and DE-ENERGIZE starter before performing any repairs or maintenance.
15 SECTION 11: TROUBLE SHOOTING GUIDE Refer to separate engine manual packed with your mower for more engine related information. NOTE: For repairs beyond the minor adjustments listed above, contact your nearest authorized service dealer. Trouble Possible Cause(s) Corrective Action Engine fails to start Blade control handle disengaged.
16 Model 109T 35 39 38 41 36 40 28 29 32 34 43 42 27 31 33 35 45 44 46 47 22 23 3 2 1 6 12 21 18 13 15 14 16 4 5 6 12 21 18 14 13 16 8 11 9 10 17 26 7 24 25 37 15 20 30 19 48 49.
17 Model 109T Ref. No. Part No. Part Description 1. 17098 Hinge Clip 2. 731-0872A Rear Flap 3. 682-3025 Handle Bracket Ass’y LH 4. 682-3024 Handle Bracket Ass’y RH 5. 712-0431 Flange Lock Nut 3/8-16 6. 731-1426 Hub Cap-Yellow 7. 682-0139 Deck Assembly 8.
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD PRODUCTS INC (“MTD”) with respect to new merchan- dise purchased and used in the United States, its posses- sions and territories.
An important point after buying a device Yard-Man 109T (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Yard-Man 109T yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Yard-Man 109T - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Yard-Man 109T you will learn all the available features of the product, as well as information on its operation. The information that you get Yard-Man 109T will certainly help you make a decision on the purchase.
If you already are a holder of Yard-Man 109T, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Yard-Man 109T.
However, one of the most important roles played by the user manual is to help in solving problems with Yard-Man 109T. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Yard-Man 109T along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
