Instruction/ maintenance manual of the product RX-V592RDS Yamaha
Go to page of 55
OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING Natural Sound A V Receiver Récepteur audiovisuel “Son Naturel”.
2 ● Indoor FM Antenna ● Antenne FM intérieure ● UKW-Innenantenne ● FM inomhusantenn ● Antenna FM interna ● Antena FM interior ● FM Binnenantenne ● AM Loop Antenna ● Cadre-antenna AM ● MW-Rahmenantenne ● AM ramantenn ● Antenna AM ad anello ● Antena de cuadro de AM ● AM Lusantenne ● 75-ohm/300-ohm antenna adapter (U.
FEA TURES CONTENTS 3 English ● 5 Speaker Configuration RX-V692RDS Main: 75W + 75W (8 Ω ) RMS Output Power , 0.04% THD, 20–20,000 Hz Center: 75W (8 Ω ) RMS Output Power , 0.07% THD, 20–20,000 Hz Rear: 40W + 40W (8 Ω ) RMS Output Power , 0.3% THD, 1 kHz RX-V592RDS Main: 70W + 70W (8 Ω ) RMS Output Power , 0.
CAUTION : READ THIS BEFORE OPERA TING YOUR UNIT . 4 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold.
5 English NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use only AA, R6, UM-3 batteries for replacement.
6 PROFILE OF THIS UNIT You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences.
7 English SPEAKER SETUP SPEAKERS T O BE USED This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker.
8 CONNECTIONS Never plug in this unit and other components until all connections are completed. CONNECTIONS WITH OTHER COMPONENTS When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L , R (right) to R , “ + ” to “ + ” and “ – ” to “ – ”.
9 English AC OUTLET(S) (SWITCHED) (Europe model) ................................. 2 SWITCHED OUTLETS (U.K. model) ....................................
10 Connecting with a Dolby Digital (AC-3) Decoder If you have a Dolby Digital (AC-3) Decoder unit or an LD player etc. which incorporates a Dolby Digital (AC-3) Decoder, its discrete outputs can be connected to this unit.
11 English CONNECTING TO S VIDEO TERMINALS If you have a video cassette recorder and a monitor equipped with “S” (high-resolution) video terminals, those terminals can be connected to this unit’s S VIDEO terminals.
12 CONNECTING SPEAKERS MAIN CENTER REAR (SURROUND) OUTPUT SUB WOOFER REAR (SURROUND) CENTER CD DUAL SINGLE CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING. MAIN SPEAKERS A B A B REAR 6 Ω MIN./SPEAKER SINGLE : 6 Ω MIN./SPEAKER DUAL :3 Ω MIN./SPEAKER A OR B :4 Ω MIN.
13 English For connecting to the MAIN SPEAKERS terminals Red: positive (+) Black: negative (–) ➀ Unscrew the knob. ➁ Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Tighten the knob and secure the wire.
14 MAIN OUTPUT terminals These terminals are for main channel line output. There is no connection to these terminals when you use the built-in amplifier.
15 English ANTENNA CONNECTIONS ● Each antenna should be connected to the designated terminals correctly, referring to the following diagram. ● Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength.
16 CONTROLS AND THEIR FUNCTIONS FRONT P ANEL PRO LOGIC ENHANCED 70 mm MOVIE THEATER TV SPORTS STADIUM POWER NATURAL SOUND AV RECEIVER RX–V692RDS SPEAKERS PHONES A ON OFF ON OFF B BASS TREBLE BALANCE.
17 English 1 POWER switch Press this switch to switch the power on. Press it again to switch the power off. 2 Standby mode indicator While the power is on, pressing the POWER (SYSTEM POWER OFF) key on the remote control transmitter switches the unit to the standby mode.
18 I PTY SEEK MODE button When this button is pressed, the unit turns into the PTY SEEK mode. J PTY SEEK START button Press this button to begin searching for a station after the desired program type is selected in the PTY SEEK mode.
19 English DISPLA Y P ANEL PRESET kHz MHz MEMORY AM FM SLEEP AUTO TAPE 2 MONITOR DIGITAL STEREO 0 20 l00 ROOM 2 CONTROL NORMAL WIDEPHANTOM 40 60 SPEAKERS RT PS PTY PTY HOLD EON NEWS INFO AFFAIRS SPORT.
20 0 PTY HOLD indicator Lights up while the search is performed in the PTY SEEK mode. A EON indicator Lights up when an RDS station that employs the EON data service is received. B Program type name indicators The name selected in the EON mode lights up.
21 English For Control of This Unit 1 DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/– keys Adjust the delay time (DELAY), the center channel output level (CENTER), the rear channel output level (REAR) and the output level to the SUBWOOFER OUTPUT terminal (SWFR).
22 TEST 1 Set to the “ ∞ ” position. 2 Turn the power on. 3 Select the main speakers to be used. * If you use two main speaker systems, press both the A and B switches.
23 English l6 20 28 40 60 l2 8 4 2 0 –dB 7 Select the center channel output mode suitable for your speaker configuration. (Refer to “ SPEAKER CONFIGURATION ” on page 7.) On the feature of each mode, refer to the “ Note ” shown below. Note In step 7, when you select a center channel output mode, note the following.
10 Adjust the sound output levels of the center speaker and the rear speakers so that they become almost as same as that of the main speakers. a) Press once or more so that “CENTER” or “REAR” appears on the display.
25 English 1 Set to the “ ∞ ” position. 2 Turn the power on. 3 Select the desired input source by using the input selector buttons. (For video sources, turn the TV/monitor ON.) * The name of the selected input source will appear on the display. 4 Select the main speakers to be used.
26 1 Select the source to be recorded. 2 Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to the page 28.) 3 Begin recording on the tape deck (or MD recorder etc.
27 English Selecting the SPEAKER system Because one or two speaker systems (as main speakers) can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B , or both at once.
28 1 Select the reception band (FM or AM) confirming it on the display. 2 3 Tune to a desired station manually. * To continue tuning search, press and hold the button. 1 Select the reception band (FM or AM) confirming it on the display. 2 3 To tune to a higher frequency, press the right side once.
29 English 1 Tune to a desired station. (Refer to the previous page for tuning procedure.) 2 Select a desired group (A – E) of preset stations confirming it on the display. 3 4 Select a preset station number where you want to program the station before “MEMORY” goes off from the display.
30 1 2 3 To tune to higher frequencies, press right side once. To tune to lower frequencies, press left side once. * If the TUNING button is not pressed, in a while, the automatic preset tuning begins automatically toward higher frequencies. The automatic preset tuning begins from the frequency currently displayed.
31 English EXCHANGING PRESET ST A TIONS You can exchange the places of two preset stations with each other as shown below. Example) If you want to shift the preset station on E1 to A5, and vice versa. 1 Recall the preset station on E1 (by following the method of “To recall a preset station” on page 29).
32 RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal.
33 English News: Short accounts of facts, events and publicly expressed views, reportage and actuality. Current affairs: Topical program expanding or enlarging upon the news, generally in different presentation style or concept, including documentary debate, or analysis.
34 Changing the RDS modes When an RDS station is received, “PS”, “PTY”, “RT” and/or “CT” that correspond to the RDS data services employed by the station light up on the display.
35 English 1 Turn the unit into the PTY SEEK mode. * The program type of the station now being received or “NEWS” flashes on the display. 2 Select the desired program type. 3 Begin searching all preset RDS stations. * “PTY HOLD” lights up on the display.
36 1 Make sure that “EON” is illuminated on the display. * If “EON” is not illuminated on the display, receive an (or another) RDS station so that “EON” lights up on the display. 2 Select a desired program type, NEWS, INFO, AFFAIRS or SPORT.
Brief Overview of Digital Sound Field Pr ograms The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments.
38 PROGRAM FEATURE 70 mm This program is effective for playback of sources encoded with Dolby Surround. MOVIE THEATER The Yamaha DSP technology is ideally combined with the Dolby Pro Logic to present you incredible listening experience of the 70 mm film movie theater.
39 English 1 Follow steps 1 – 6 shown in “ BASIC OPERATIONS ” on page 25. 2 Select the desired program that is suitable for the source. The selected program name is shown on the display. 3 If desired, adjust the delay time and the output level of each speaker.
40 If desired, you can adjust the sound output level of the center speaker even if the output level is already set in “ SPEAKER BALANCE ADJUSTMENT ” on page 24.
Adjustment of DELA Y TIME You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the effect sound from the rear speakers. The larger the value, the later the effect sound is generated. This adjustment can be made to all programs individually.
42 1 Whenever the SLEEP key is pressed, the SLEEP time will change as follows. After a while, the display returns to the indication before the SLEEP timer is set. 2 The unit will be turned off automatically at the selected SLEEP time. SETTING THE SLEEP TIMER If you use the SLEEP timer of this unit, you can make this unit turn off automatically.
43 English B ASIC OPERA TIONS (When the lid is open) The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit.
44 1 Tape deck keys Controls tape deck. (The A/B/C switch ( F ) should be set to the “A” position.) * DIR A, B and A/B are applicable only to double cassette tape deck. * For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direction of tape running.
45 English LEARNING NEW CONTR OL FUNCTIONS (When the lid is open) This is a learning remote control transmitter. The shaded keys in the illustration shown below can be programmed to “learn” control functions from other remote control transmitters.
46 Note If a key which has a preset function learns a new function, the preset function will not be deleted, but disabled. When the learned function is cleared, the preset function is restored. (For information on clearing a learned function, refer to page 52.
47 English When the lid is closed, the OPERATION CONTROL keys substitute for the keys numbered 1 , 2 , 3 and the ( +10 ) key on the left illustration. To use these keys, you do not have to switch the A/B/C switch.
48 MA CRO OPERA TIONS (When the lid is closed) “Macro” is a command which defines a sequence of several operations. The keys shown in the illustrations below (as preset macro keys ) are also preset with macros, in addition to individual functions.
49 English Macro key 1st (Turning the power of this unit on) 2nd (Selecting an input source) 3rd (Playing a source) “” on area A of keys 1 “” on area A of keys 2 – “” on area B of keys 1.
50 LEARNING A NEW FUNCTION 1 Place this remote control transmitter and the other remote control transmitter so that they face each other. 2 * If there is no operation for about 30 seconds after the LEARN button is pressed, the TRANSMIT/LEARN indicator flashes rapidly and the current mode is canceled.
1 * If there is no operation for about 30 seconds after the MACRO button is pressed, the TRANSMIT/LEARN indicator flashes rapidly and the mode before you pressed the MACRO button is restored. If this occurs, press the MACRO button again. 2 Press a preset macro key on which you want to make a new macro.
52 1 To clear a learned key function, press the LEARN button using the point of a mechanical pencil, etc. To clear a macro you made, press the MACRO button.
53 English Amplifier FM AM Others Remote control transmitter TR OUBLESHOO TING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested.
54 SPECIFICA TIONS AUDIO SECTION Minimum RMS Output Power per Channel Main L, R 8 ohms, 20 Hz to 20 kHz, 0.04% THD < RX-V692RDS > .......................75W+75W < RX-V592RDS > .......................70W+70W Center 8 ohms, 20 Hz to 20 kHz, 0.
SPECIFICA TIES AUDIO GEDEELTE Minimum RMS uitgangsvermogen per Kanaal Hoofd 8 ohm, 20 Hz tot 20 kHz, 0,04% Totale Harmonische Vervorming < RX-V692RDS > .......................75W+75W < RX-V592RDS > .......................70W+70W Midden 8 ohm, 20 Hz tot 20 kHz, 0,07% Totale < RX-V692RDS > .
An important point after buying a device Yamaha RX-V592RDS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Yamaha RX-V592RDS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Yamaha RX-V592RDS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Yamaha RX-V592RDS you will learn all the available features of the product, as well as information on its operation. The information that you get Yamaha RX-V592RDS will certainly help you make a decision on the purchase.
If you already are a holder of Yamaha RX-V592RDS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Yamaha RX-V592RDS.
However, one of the most important roles played by the user manual is to help in solving problems with Yamaha RX-V592RDS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Yamaha RX-V592RDS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
