Instruction/ maintenance manual of the product RX-V392RDS Yamaha
Go to page of 43
O WNER’S MANU AL MODE D’EMPLOI BEDIENUNGSANLEITUNG BR UKSANVISNING MANU ALE DI ISTR UZIONI MANU AL DE INSTR UCCIONES GEBR UIKSAANWIJZING Natural Sound A V Receiver Récepteur audiovisuel “Son Na.
2 ● Indoor FM Antenna ● Antenne FM intérieure ● UKW-Innenantenne ● FM inomhusantenn ● Antenna FM interna ● Antena FM interior ● FM Binnenantenne ● AM Loop Antenna ● Cadre-antenna AM ● MW-Rahmenantenne ● AM ramantenn ● Antenna AM ad anello ● Antena de cuadro de AM ● AM Lusantenne ● 75-ohm/300-ohm antenna adapter (U.
FEA TURES CONTENTS 3 English ● 5 Speaker Configuration RX-V492RDS Main: 65W + 65W (8 Ω ) RMS Output P ower , 0.04% THD , 20–20,000 Hz Center: 65W (8 Ω ) RMS Output P ower , 0.09% THD , 1 kHz Rear: 20W + 20W (8 Ω ) RMS Output P ower , 0.7% THD , 1 kHz RX-V392RDS Main: 50W + 50W (8 Ω ) RMS Output P ower , 0.
CA UTION : READ THIS BEFORE OPERA TING Y OUR UNIT . 4 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold.
5 English NO TES ABOUT THE REMO TE CONTROL TRANSMITTER Battery installation Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use only AA, R6, UM-3 batteries for replacement.
6 PR OFILE OF THIS UNIT You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences.
7 English SPEAKER SETUP SPEAKERS T O BE USED This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker.
8 CONNECTIONS Never plug in this unit and other components until all connections are completed. CONNECTIONS WITH O THER COMPONENTS When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L , R (right) to R , “ + ” to “ + ” and “ – ” to “ – ”.
9 English A C OUTLET(S) (SWITCHED) (Europe model) ................................. 2 SWITCHED OUTLETS (U.K. model) ...................................
10 CONNECTING SPEAKERS CENTER OUTPUT SUB WOOFER REAR CENTER CD DUAL SINGLE CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING. MAIN SPEAKERS A B REAR 6 Ω MIN./SPEAKER SINGLE : 6 Ω MIN./SPEAKER DUAL :3 Ω MIN./SPEAKER A OR B :4 Ω MIN./SPEAKER A B :8 Ω MIN.
11 English For connecting to the MAIN SPEAKERS terminals Red: positive (+) Black: negative (–) ➀ Unscrew the knob. ➁ Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Tighten the knob and secure the wire.
12 CENTER OUTPUT terminal This terminal is for center channel line output. There is no connection to this terminal when you use the built-in amplifier. However, if you drive a center speaker with an external power amplifier, connect the input terminal of the external amplifier to this terminal.
13 English ANTENNA CONNECTIONS ● Each antenna should be connected to the designated terminals correctly, referring to the following diagram. ● Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength.
14 CONTR OLS AND THEIR FUNCTIONS FR ONT P ANEL PRO LOGIC ENHANCED CONCERT VIDEO MONO MOVIE STADIUM POWER NATURAL SOUND AV RECEIVER RX–V492RDS SPEAKERS PHONES A ON B OFF BASS TREBLE BALANCE VOLUME 55.
15 English 1 POWER switch Press this switch to switch the power on. Press it again to switch the power off. 2 Standby mode indicator While the power is on, pressing the POWER key on the remote control transmitter switches the unit to the standby mode.
16 J MEMORY (MAN’L/AUTO FM) button When this button is pressed, the MEMORY indicator flashes for about 5 seconds. During this period, select a desired preset station number by pressing the corresponding preset station number selector button to enter the displayed station into the memory.
17 English DISPLA Y P ANEL PRESET kHz MHz MEMORY AUTO PTY HOLD SLEEP TAPE MON STER EO 0 20 l00 ms d B PRO LOGIC ENHANCED CONCERT VIDEO MONO MOVIE STADIUM DISCO ROCK CONCERT CONCERT HALL NORM WIDE PHAN.
18 REMO TE CONTROL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit.
19 English For Contr ol of This Unit 1 DELAY/CENTER/REAR and TIME/LEVEL +/– keys RX-V492RDS only Adjust the delay time (DELAY), the center channel output level (CENTER) and the rear channel output level (REAR).
REC/PAUSE DIR B DIR A PLAY DISC POWER VOLUME PLAY PRESET A/B/C/D/E –+ TIME/ LEVEL TEST EFFECT PROGRAM PROLOGIC ENHANCED –+ SLEEP TAPE A/B ON/OFF TUNER CD PHONO DELAY/CENTER /REAR DVD/LD VCR TV/DBS 20 1 Set to the “ ∞ ” position. 2 Turn the power on.
21 English l6 20 28 40 60 l2 8 4 2 0 –dB 6 Select the center channel output mode suitable for your speaker configuration. (Refer to “ SPEAKER CONFIGURATION ” on page 7.) On the feature of each mode, refer to the “ Note ” shown below. Note In step 6, when you select a center channel output mode, note the following.
9 Adjust the sound output levels of the center speaker and the rear speakers so that they become almost as same as that of the main speakers. Make the adjustment of each speaker output level at your listening position with the remote control transmitter.
23 English 1 Set to the “ ∞ ” position. 2 Turn the power on. 3 Select the desired input source by using the input selector buttons. (For video sources, turn the TV/monitor ON.) * The name of the selected input source will appear on the display. 4 Select the main speakers to be used.
24 1 Select the source to be recorded. 2 Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to the page 26.) 3 Begin recording on the tape deck (or MD recorder etc.
25 English Selecting the SPEAKER system Because one or two speaker systems (as main speakers) can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B , or both at once.
26 1 Select the reception band (FM or AM) confirming it on the display. 2 3 Tune to a desired station manually. * To continue tuning search, press and hold the button. 1 Select the reception band (FM or AM) confirming it on the display. 2 3 To tune to a higher frequency, press the right side once.
27 English 1 Tune to a desired station. (Refer to the previous page for tuning procedure.) 2 Select a desired group (A – E) of preset stations confirming it on the display. 3 4 Select a preset station number where you want to program the station before “MEMORY” goes off from the display.
28 1 2 3 To tune to higher frequencies, press right side once. To tune to lower frequencies, press left side once. * If the TUNING button is not pressed, in a while, the automatic preset tuning begins automatically toward higher frequencies. The automatic preset tuning begins from the frequency currently displayed.
29 English EXCHANGING PRESET ST A TIONS You can exchange the places of two preset stations with each other as shown below. Example) If you want to shift the preset station on E1 to A5, and vice versa. 1 Recall the preset station on E1 (by following the method of “To recall a preset station” on page 27).
30 RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal.
31 English News: Short accounts of facts, events and publicly expressed views, reportage and actuality. Current affairs: Topical program expanding or enlarging upon the news, generally in different presentation style or concept, including documentary debate, or analysis.
32 Changing the RDS modes When an RDS station is received, “PS”, “PTY”, “RT” and/or “CT” that correspond to the RDS data services employed by the station light up on the display.
33 English 1 Turn the unit into the PTY SEEK mode. * The program type of the station now being received or “NEWS” flashes on the display. 2 Select the desired program type. 3 Begin searching all preset RDS stations. * “PTY HOLD” lights up on the display.
34 1 Make sure that “EON” is illuminated on the display. * If “EON” is not illuminated on the display, receive an (or another) RDS station so that “EON” lights up on the display. 2 Select a desired program type, NEWS, INFO, AFFAIRS or SPORT.
Brief Overview of Digital Sound Field Pr ograms The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments.
36 1 Follow steps 1 – 6 shown in “ BASIC OPERATIONS ” on page 23. 2 Select the desired program that is suitable for the source. a) Turn the DSP on so that a program name lights up on the display. b) Select a desired program confirming it on the display.
37 English If desired, you can adjust the sound output level of the center speaker even if the output level is already set in “ SPEAKER BALANCE ADJUSTMENT ” on page 22.
Adjustment of DELA Y TIME You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the effect sound from the rear speakers. The larger the value, the later the effect sound is generated. This adjustment can be made to all programs individually.
39 English 1 Whenever the SLEEP key is pressed, the SLEEP time will change as follows. After a while, the display returns to the indication before the SLEEP timer is set.
40 Amplifier FM AM Others Remote control transmitter TR OUBLESHOO TING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested.
41 English SPECIFICA TIONS A UDIO SECTION Minimum RMS Output Power per Channel Main L, R 8 ohms, 20 Hz to 20 kHz, 0.04% THD < RX-V492RDS > .........................................65W+65W < RX-V392RDS > ....................................
42 SPECIFICA TIONS VIDEO SECTION Video Signal Type .....................................................PAL Video Signal Level ..................................1 Vp-p/75 ohms Maximum Input Level ............................1.5 Vp-p or more Signal-to-Noise Ratio .
284 VY70040 Printed in France SPECIFICA TIES VIDEO GEDEEL TE Video-signaaltype ......................................................PAL Video-signaalniveau ..................................1 Vp-p/75 ohm Maximum ingangsniveau .......................1,5 Vp-p of meer Signaal/ruis verhouding .
An important point after buying a device Yamaha RX-V392RDS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Yamaha RX-V392RDS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Yamaha RX-V392RDS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Yamaha RX-V392RDS you will learn all the available features of the product, as well as information on its operation. The information that you get Yamaha RX-V392RDS will certainly help you make a decision on the purchase.
If you already are a holder of Yamaha RX-V392RDS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Yamaha RX-V392RDS.
However, one of the most important roles played by the user manual is to help in solving problems with Yamaha RX-V392RDS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Yamaha RX-V392RDS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
