Instruction/ maintenance manual of the product CC-50 Yamaha
Go to page of 48
Active Servo Technology CC-50 Natural Sound Mini Component System Chaîne Mini de la série “Natural Sound” Natural Sound Mini Komponenten-System Natural Sound Mini Komponent System Sistema di Com.
● Remote control transmitter ● Télécommande ● Fernbedienung ● Fjärrkontroll ● Telecomando ● Controlador remoto ● Afstandbediening ● Batteries (size AA, UM/SUM-3, R6, HP-7) ● Piles (format AA, UM/SUM-3, R6, HP-7) ● Batterien (Größe AA, UM/SUM-3, R6, HP-7) ● Batterier (Storl.
INTRODUCTION CONTENTS E-1 English ENGLISH Page PRECAUTIONS ..................................................................2-3 ACTIVE SERVO TECHNOLOGY ..........................................3 NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS ...
NOTE Please check the copyright laws in your country to record from records, compact discs, radio, etc. Recording of copyright material may infringe copyright laws. IMPORTANT Please record the serial number of this unit in the space below. Serial No.: The serial number is located on the rear of the unit.
A CTIVE SER V O TECHNOLOGY Active Servo Processing Amplifier Port Cabinet High- amplitude bass sound Signals of low amplitude Negative-impedance output drive Air woofer (Helmholtz resonator) Signals E-3 English The theory of the Active Servo Technology is based upon two major factors, the Helmholtz resonator and negative- impedance drive.
NAMES OF CONTROLS, INDICA T ORS AND REAR P ANEL P AR TS E-4 CD Play er (CDX-S50) 1. Disc Table 2. RESUME button 3. OPEN/CLOSE Button: 4. RANDOM Play Button 5. SKIP Buttons: / ( SEARCH Buttons: / ) 6. Stop Button: 7. Play/Pause Button: / 8. Track Number Indicator 9.
E-5 English NAMES OF CONTROLS, INDICA T ORS AND REAR P ANEL P AR TS Double Cassette T ape Deck (KXW -S70) 50. DECK A Cassette Compartment 51. DECK A Select Button and Indicator 52. DECK B Select Button and Indicator 53. DECK B Cassette Compartment 54.
E-6 NAMES OF CONTROLS, INDICA T ORS AND REAR P ANEL P AR TS FREQUENCY STEP switch (General model only) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area.
Names of contr ol buttons ■ Receiver Control Buttons 1. Remote Control Transmitter Window 2. Preset Station Number Buttons 3. A, B, C, D, E Selector Buttons 4. PRESET DOWN/UP Buttons 5. A/B/C/D/E Button 6. EFFECT LEVEL Down ( – )/Up ( + ) Buttons 7.
■ CD Player Control Buttons 15. Track Number Input Buttons 16. TIME Button 17. SKIP Buttons: / ( SEARCH Buttons: / ) 18. REPEAT Button 19. RANDOM Button 20. STOP Button: 21. PLAY/PAUSE Button: 22. EDIT Button 23. TAPE Button 24. PROG RAM Button ■ Tape Deck Control Buttons 25.
E-9 English 30° 30° Remote control sensor 0.2 m – 6 m (8” – 20’) Loading the batteries f or the remote contr ol transmitter 1 Remove the battery compartment cover. (Press the left edge of the cover to right with a finger, and then pull it upward.
E-10 AM ANT GND FM ANT 75 Ω UNBAL. Placing the system This system can be placed any way you like, however, be sure not to place another unit or any object on top of the receiver to prevent the ventilation holes on the top panel of the receiver from being obstructed.
E-11 English Speaker connection Connect each speaker wire to the SPEAKERS terminals. Cautions • Do not let the bare speaker wires touch each other as this could damage the receiver and/or speakers. • When connecting the speakers to the unit, be sure to connect the speaker wires properly.
OPEN/CLOSE THE CONTROL DOOR When it is not necessary to operate controls inside the control door, close the door. To open or close the door, press the right edge until it clicks. E-12 STANDBY mode While the power is on, pressing the POWER switch (or the POWER switch on the remote control transmitter) switches the system to the STANDBY mode.
E-13 English 1 While the power is on, press the DISPLAY button to display the time. If the power is off, you can proceed to the next step. 2 While pressing the TIME ADJUST button, press the HOUR button and set the hour. * Press the HOUR button once to advance the time by 1 hour.
The Digital Sound Field Processor (DSP) built into this unit presents you with the ambience of an actual concert hall, jazz club, etc. by adding effects as sonic reflections or reberverations that create the sound environment of a hall etc. This unit provides the following 4 DSP modes that simulates actual sound environments.
E-15 English COMP A CT DISC PLA YER OPERA TION DIGIT AL SOUND FIELD PROCESSOR (DSP) CONTR OL Care of compact discs Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player.
E-16 CD pla yback 1 Select the CD player so that “CD” appears on the display by pressing the INPUT selector or button. 2 Press the OPEN/CLOSE button to open the disc table. 3 Place a disc on the table, label side up. * 8 cm (3”) disc can be played without an adaptor.
E-17 English 12 3 4 5 12 3 4 5 67 8 67 8 9 0 E + I0 TUNER DIRECT - + 12 3 4 5 12 3 4 5 67 8 67 8 9 0 AB C D E TIME PROG TAPE EDIT + I0 STOP PLAY/PAUSE RANDOM REPEAT CD TUNER TAPE PRESET DOWN UP PLAY S.
E-18 COMP A CT DISC PLA YER OPERA TION - + 12 3 4 5 12 3 4 5 67 8 67 8 9 0 AB C D E TIME PROG TAPE EDIT + I0 STOP PLAY/PAUSE RANDOM REPEAT CD TUNER TAPE PRESET DOWN UP PLAY STOP REC/PAUSE SLEEP POWER .
E-19 English COMP A CT DISC PLA YER OPERA TION Pr ogram play You can program up to 20 tracks in any desired order. 1 Load a disc and close the disc table. 2 When in the stop mode, press the PROGRAM button to prepare for programming. * “PROG” and “P-01” illuminate on the display, and all track numbers on the disc begin flashing.
/ E-20 To stop program play • Press the stop button. The first track number programmed will be displayed. • To resume playback, press the play/pause / button. Playback will begin from the beginning of the program. To cancel a programmed sequence There are several methods as described below.
E-21 English Repeat pla y An entire disc, a single track or a programmed sequence can be continuously repeated. 1 While watching the display, press the REPEAT button once or more to select a desired repeat play mode (S REP or F REP). 2 Press the play/pause button.
TRACK 2 3 4 5 6 7 8 9 10 11 12 HALL DSP ON TRACK REMAIN 2 3 4 5 6 7 8 9 10 11 12 HALL DSP ON TRACK TOTAL 2 3 4 5 6 7 8 9 10 11 12 HALL DSP ON TRACK TOTAL REMAIN 2 3 4 5 6 7 8 9 10 11 12 HALL DSP ON E-22 Random pla y The tracks on the disc can be played back in a random order.
E-23 English Normally, if station signals are strong and there is no interference, quick automatic-search tuning (Automatic tuning) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (Manual tuning).
E-24 TUNING OPERA TION Preset tuning This unit can store station frequencies selected by tuning operation. With this function, you can select any desired station by only calling the corresponding preset station number. Up to 40 stations (8 stations x 5 areas) can be stored.
E-25 English A utomatic preset tuning You can also make use of an automatic preset tuning function. By this function, this unit performs automatic tuning and stores stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on the previous page.
E-26 E-26 Detection hole Tab T APE DECK OPERA TION General inf ormation • Do not use C-120 tapes, tapes with internal reels or poor- quality tapes, since they can cause malfunctions. • Before loading a tape into the cassette compartment, tighten the slack tape with a pen or pencil.
E-27 English T ape A or tape B playbac k 1 Select the tape deck so that “TAPE” appears on the display by pressing the INPUT selector or button. 2 Open the DECK A or DECK B cassette compartment by pressing the EJECT button.
E-28 Winding the tape 1 If during playback, first press the stop button. 2 Next press the fast wind or fast wind button to wind the tape. 3 Press the stop button to stop. * While winding the tape, the corresponding play direction indicator flashes rapidly.
E-29 English Continuous pla ybac k 1 Load the tapes into the DECK A and DECK B cassette compartments. 2 Set the reverse mode switch to . The reverse mode switch can be operated before or during playback, and changes tape playback as follows: 3 Press the DECK A or B select button to select the tape to be played back first.
Side A only Side B only Side A → Side B Side B only Side A → Side B Side B only • When recording important selections, be sure to make a preliminary test to ensure that the desired source material is being properly recorded with good sound quality.
E-31 English To stop recording temporarily 1 Press the stop button of the CD player. 2 Choose the selection to be recorded next by using the SKIP or button, and then press the play button of the CD player to resume recording (or simply press the track number input button on the remote control transmitter).
E-32 Recor ding CD on both sides of a tape automatically 1 Select the CD player so that “CD” appears on the display by pressing the INPUT selector or button, and load the disc to be recorded. 2 Load a tape into the cassette compartment. 3 When recording with the Dolby NR system, set the Dolby NR switch to B or C; if not, set it to OFF.
E-33 English A utomatic tape-editing This convenient feature can be used to program tracks on a disc for recording to tape. By only memorizing the tape’s total possible recording time, the unit will.
E-34 RECORDING A COMP A CT DISC Note The CD player’s repeat play mode will be canceled during this recording mode. To cancel tape-editing function Before recording, press the stop button of the CD player or the tape deck. To stop recording Press the stop button of the tape deck.
E-35 English RECORDING A COMP A CT DISC T o record pr ogrammed tracks 1 Select the CD player so that “CD” appears on the display by pressing the INPUT selector or button, and load the disc to be recorded., and load a disc on the disc table. 2 Follow steps 2–5 on page 33.
E-36 Recor ding from the b uilt-in tuner 1 Select the tuner so that “TUNER” appears on the display by pressing the INPUT selector or button. 2 Tune to the desired station. (Refer to the “TUNING OPERATION” on pages 23 and 24.) 3 Load a tape into the cassette compartment.
Dubbing • During dubbing, adjusting the VOLUME, BALANCE, TREBLE and BASS controls have no effect on the recorded sound. If, however, the DSP is on, the DSP effect is recorded along with the source. * Music with DSP effect is suitable for listening to inside a car etc.
E-38 HO W T O USE THE BUIL T -IN TIMER Timer pla y By using the built-in timer, you can set the time when the unit turns on and a source begins playing automatically, and the time when the unit turns off automatically. 1 Prepare the source to be played.
E-39 English ➂ At ON TIME/time setting mode [“ON TIME” appears on the display, and soon it is changed to a time setting mode.] Set to the time when the timer play begins by using the HOUR button and the MINUTE button. ➃ At OFF TIME/time setting mode [“OFF TIME” appears on the display, and soon it is changed to a time setting mode.
E-40 To begin CD playback from a desired track by the timer play. 1. Play back the track which you want to play back from the beginning of the timer play. 2. Press the RESUME button on the CD player so that “ ” appears on the display. 3. Make the timer play setting.
E-41 English HO W T O USE THE BUIL T -IN TIMER Sleep timer operation This unit can be turned off automatically. 1 Play the desired sound source. 2 Press the SLEEP button. “SLEEP” appears on the display, and soon it is replaced by “120”. 3 Press the SLEEP button repeatedly until the desired sleep time appears in the display.
E-42 INPUT PHONO AUX R L A uxiliary (A UX) 1 Connect the output lead of a video cassette player, video disc player, etc. to the AUX inputs of this unit. (red → right channel, white → left channel) 2 Press the INPUT selector or button once or more until “AUX” appears on the display.
E-43 English PHONES Headphones • Be sure that your headphones have a 3.5 mm (1/8”) diameter plug and are between 16 ohms and 50 ohms impedance. Recommended impedance is 32 ohms. • When headphones are connected, the speakers are defeated automatically.
E-44 SPECIFICA TIONS As a part of policy of continuous improvement, YAMAHA reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units.
E-45 English E-45 CAUSE AC supply lead is not plugged in. Loose speaker connections. Internal protection circuit is functioning. Interference from starting motor of nearby car. Interference from thermostat of nearby electrical appliance. Antenna input is too weak due to obstructions or excessive distance from broadcasting station.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.
An important point after buying a device Yamaha CC-50 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Yamaha CC-50 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Yamaha CC-50 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Yamaha CC-50 you will learn all the available features of the product, as well as information on its operation. The information that you get Yamaha CC-50 will certainly help you make a decision on the purchase.
If you already are a holder of Yamaha CC-50, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Yamaha CC-50.
However, one of the most important roles played by the user manual is to help in solving problems with Yamaha CC-50. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Yamaha CC-50 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
