Instruction/ maintenance manual of the product AX-890 Yamaha
Go to page of 14
Natural Sound Stereo Integrated Amplifier Préampli/ampli de puissance stéréo de la série “Natural Sound” Natural Sound Stereo-V erstärker Natural Sound Integrerad Stereo Förstärkare Amplifi.
This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or 87/308/EEC. Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE. Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG.
● 110W + 110W (8 Ω ) RMS Output Power, 0.015% THD, 20–20,000 Hz ● High Dynamic Power, Low Impedance Drive Capability ● Continuously Variable Loudness Control ● CD DIRECT AMPLIFIER to Repro.
4 CONNECTIONS ● Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made.
5 English Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed.
6 OPERA TIONS T O PLA Y A SOURCE 1 Set to the “ ∞ ” position. 2 Turn the power on. 3 Select a desired input source. * If you select turntable as an input source (PHONO position), you should confirm that the PHONO (MM/MC) switch is set to the position corresponding to the type of cartridge being used by the turntable.
1 Select the source to be recorded. 2 Play the source. 3 Confirm the source by selecting it with the INPUT selector and turning up the VOLUME control. 4 Set the tape deck to be used for recording in the recording mode. 5 To monitor the sound to be recorded (or being recorded), select the tape deck being used for recording with the INPUT selector.
8 Adjusting the B ASS and TREBLE controls Adjusting the B ALANCE contr ol Selecting the SPEAKER system Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused from speaker location or listening room conditions.
9 English Setting the SUBSONIC FIL TER switch When y ou listen with headphones Connect the headphones to the PHONES jack. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position. Open/close the contr ol door When it is not necessary to operate controls inside the control door, close the door.
10 REMO TE CONTR OL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit.
11 English NO TES ABOUT THE REMO TE CONTR OL TRANSMITTER Battery installation Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use only AA, R6, UM-3 batteries for replacement.
12 SYMPTOM The unit fails to turn on when the POWER switch is pressed. No sound. The sound suddenly goes off. Only one side speaker outputs the sound. There is a lack of bass, and no ambience. Sound “hums”. Sound level is low or sound is distorted while playing a record on the turntable.
13 English SPECIFICA TIONS Minimum RMS Output Power per Channel 8 ohms, 20 Hz to 20 kHz, 0.015% THD ...............................................110W+110W 6 ohms, 20 Hz to 20 kHz, 0.03% THD ...............................................130W+130W Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) 8/6/4/2 ohms .
SPECIFICA TIES Minimum RMS uitgangsvermogen per Kanaal 8 ohm, 20 Hz tot 20 kHz, 0,015% Totale Harmonische Vervorming .........110W+110W 6 ohm, 20 Hz tot 20 kHz, 0,03% Totale Harmonische Vervorming .........130W+130W Dynamische Vermogen per Kanaal (IHF Meetmethode voor Vrij Dynamisch Bereik) 8/6/4/2 ohm .
An important point after buying a device Yamaha AX-890 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Yamaha AX-890 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Yamaha AX-890 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Yamaha AX-890 you will learn all the available features of the product, as well as information on its operation. The information that you get Yamaha AX-890 will certainly help you make a decision on the purchase.
If you already are a holder of Yamaha AX-890, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Yamaha AX-890.
However, one of the most important roles played by the user manual is to help in solving problems with Yamaha AX-890. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Yamaha AX-890 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
