Instruction/ maintenance manual of the product AX-496/396 Yamaha
Go to page of 17
AX- 4 96/ 3 96 STEREO AMPLIFIER AMPLIFICA TEUR STEREO O WNER’S MANU AL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANU ALE DI ISTR UZIONI MANU AL DE INSTR UCCIONES GEBR UIKSAANWIJZING G B.
UNP A CKING After unpacking, chec k that the follo wing items are contained. DEB ALLA GE Après le déballage, vérifier que les pièces suiv antes sont incluses. A USP A CKEN Nach dem Auspac ken überprüfen, ob die f olgenden T eile v orhanden sind.
English E- 1 Thank you f or selecting this Y AMAHA stereo amplifier . FEA TURES v AX-496 85W + 85W (8 Ω ) RMS Output P ower , 0.019% THD, 20–20,000 Hz AX-396 60W + 60W (8 Ω ) RMS Output P ower , 0.
E- 2 1. T o assure the finest performance, please read this manual carefully . K eep it in a safe place f or future reference . 2. Install this unit in a cool, dry , clean place – awa y from windows, heat sources , sources of e xcessive vibration, dust, moisture and cold.
English E- 3 Remote control operation range Notes ● The area between the remote control and the main unit must be clear of large obstacles. ● Do not expose the remote control sensor to strong lighting, in par ticular , an inverter type fluorescent lamp; otherwise, the remote control ma y not wor k properly .
E- 4 GND PHONO 2 TUNER 3 IN (PLAY) 4 TAPE OUT (REC) 3 IN (PLAY) 4 OUT (REC) MD AUX A B CAUTION :SEE INSTRUCTION MANUAL FOR CORRECT SETTING. SPEAKERS IMPEDANCE SELECTOR AC OUTLETS SET BEFORE POWER ON A OR B : 6 Ω MIN. /SPEAKER A B : I2 Ω MIN. /SPEAKER A OR B : 4 Ω MIN.
English E- 5 1 2 3 Connecting speaker s Connect the SPEAKERS terminals to your speakers with the wire with the proper gauge (keep it as short as possible). If the connections are f aulty , no sound will be heard from the speakers . Make sure that the + and – polarity markings of the speaker wires are obser v ed and set correctly .
E- 6 FRONT P ANEL CONTR OLS AND THEIR FUNCTIONS AX-396 AX-496 NATURAL SOUND STEREO AMPLIFIER AX–396 VOLUME l6 20 28 40 60 l2 8 4 2 0 –dB PHONES BASS 55 4 3 2 l 0 l 2 3 4 TREBLE 55 4 3 2 l 0 l 2 3 .
English E- 7 1 PO WER Press this s witch inward (ON) to use this unit. In this state, y ou can turn on this unit or tur n this unit in the standby mode b y pressing ST ANDBY/ON . Press this s witch to release it outward (OFF) to completely cut off this unit’ s power supply from the A C line.
E- 8 For Control of This Unit 1 ST ANDBY/ON Press this ke y to turn on this unit or tur n it into the standb y mode. This ke y can be used only when the PO WER s witch on the main unit is set in the ON position. Standby mode In this state, this unit consumes a v ery small quantity of power to receiv e infrared-signals from the remote control.
English E- 9 1 Set to the “ ∞ ” position. 2 Press PO WER inward (ON). 3 If the ST ANDBY indicator is illuminated, press ST ANDBY/ON to turn on the power . (The ST ANDBY indicator turns off.) 4 Select the desired input source. The indicator of the selected source lights up .
E- 10 1 Select the source you want to record. 2 Play the source . 3 Select the source with the INPUT selector and adjust V OLUME to check the sound output. m Recor ding a sour ce to tape (or MD) AX-496 4 Begin recording on the tape deck (or MD recorder).
English E- 11 1 Select the source you want to record. 2 Play the source and then turn V OLUME up to chec k the sound output. 3 Begin recording on the tape deck (or MD recorder). 4 If the tape deck is used f or recording, you can monitor the sound of recording.
E- 12 Adjusting the B ALANCE control Adjust the balance of the output volume to the left and right speakers to compensate f or sound imbalance caused b y speaker location or listening room conditions . Using the CD/D VD DIRECT AMP switc h Y ou can enjoy the purest possible sound from y our CD or D VD play er by pressing this s witch.
English E- 13 Problem The unit cannot be turned on or turns off suddenly soon after the power is turned on. This unit does not work normall y . No sound. The sound suddenly goes off. Only one of the speakers produces the sound. There is a lack of bass and no ambience.
E- 14 SPECIFICA TIONS Power Section Minimum RMS Output P ower 8 Ω , 20 Hz to 20 kHz, 0.019% THD < AX-496 > ...................................................... 85W+85W < AX-396 > ...................................................... 60W+60W Maximum Output P ow er (EIAJ) (1 kHz, 10% THD) < AX-496 > 8/6 Ω .
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.
An important point after buying a device Yamaha AX-496/396 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Yamaha AX-496/396 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Yamaha AX-496/396 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Yamaha AX-496/396 you will learn all the available features of the product, as well as information on its operation. The information that you get Yamaha AX-496/396 will certainly help you make a decision on the purchase.
If you already are a holder of Yamaha AX-496/396, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Yamaha AX-496/396.
However, one of the most important roles played by the user manual is to help in solving problems with Yamaha AX-496/396. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Yamaha AX-496/396 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
