Instruction/ maintenance manual of the product CTYK..U7X(2,5)A Bertazzoni
Go to page of 16
Installation, Service and User Instructions BUILT-IN GAS/ELECTRIC COOKTOP BERTAZZONI DIMENSIONS: 48’’( 1216 mm ) (W) x 25 1/8’’ ( 640mm ) (D) MODELs: CTYK.
2 IMPORTANT - PLEASE READ AND FOLLOW -Before beginning installation, please read t hese instructions completely and carefully. -Do not remove permanently affixed labels, wa rnin gs, or plates fro m the product. This may void the warranty. -Please observe al l local and national codes and ordinances.
3 WARNING Read this instruction bookl et before installing and using the applia nce. The manufacturer will not be res ponsible for any damage to property or to persons caused by incorrect installation or improper use of the ap pliance.
4 WARNING: Do not use aerosol spray s in the vicini ty of this appliance while it is in operation Requirements Room ventilation – Location and v enting. ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in conformity with the appropriate national and loc al stand ards.
5 ELECTRIC GRIDDLE INSTALLATION INSTRUCTIONS For installation the electric griddl e, s ee t he instructions indicated in the figure.
6 INSTALLATION SIDE-BY-SIDE TO KI TCHEN CABINET 1. This range may be installed directly ad jace nt to existing 36" (91.5 cm) high cabinets. IMPORTANT: The top border of the worktop should be at the same level of the adjacent cabinet countertop. This can be accomplished by raising the unit usin g the ad justment spindles on the legs.
7 COOKER HOOD INSTALLATION The bottom of the hood should be 2 5 ½ " (65 cm) min. to 31 ½ " (80 cm) above the countertop. Refer to the ran gehood installation instructions for additional i nformation. These dim ensions provide for safe and efficient op eration of the hood.
8 Wiring diagram For freestanding gas range model CTYK..U7X(2,5)A CAUTION : label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. GAS CONNECTION All gas connections must be made accordi ng to national and lo cal codes.
9 valve during any pressure testing of the gas s upply pi ping system at test pressures equal to or less than 1/2 psig (3.45 kPa). 3. Flexible Connections : a) If the unit is to be installed with flex.
10 - CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS: To change the nozzles of the burners use the follo wing procedure: Lift up the burners and unscr ew the nozzles ( Fig.) using an ad justable spanner of 7 m m and change the nozzles with those designed for the ne w gas supply according to the information given i n TABLE shown below.
11 REGULATION OF BURNERS Work surface bu rn er adjustment : follow the instructions below to adjust the work surface burner minim um: 1) Light the burner and set the knob to the MINIMUM position (small flame). 2) Remove the knob of the valve that is press fit on the rod of that valve.
12 Do not to cover the burners of coo ktop with aluminium paper Keeping appl iance area clear and free fr om combustibl e materials, gasoline and oth er flammable vapors and liquid. Do not store dangero us or flammable material in the c abinet areas abo v e appliance; store them in a safe place in order to avoid pote ntial hazards .
13 USING BURNERS A diagram is etched on the control pan el above each kno b which indicates which burn er corresponds to that knob. (flame) Manual ignition: Manual ignition is always possible even when the power is cut off or in the event of prol onged power failure.
14 USING THE ELECTRIC GRIDDLE WARNING The griddle element is hot after use. Allow suffici ent time for grid dle components cool b efore cleaning. The electric griddle element is rated 120 volts AC 1100 watts. Seasoning the griddle Before using the griddle for the first time, it must be seasoned.
15 CLEANING THE APPLIANCE: Never use abrasi ve cleaners Before cleaning the appliance it shoul d be disconnec ted from the power sup ply. Cleaning the work surface: periodically cl ean the burner heads , the cast iron pan suppo rts and the burner cap s using warm water.
16 AFTER SALE SERVICE: Please note here belo w details for after save service. Refer to warranty certific ate for warranty condiftions Dealer /Importer: Name, address, phone MANUFACTURER: BERTAZZONI SPA VIA PALAZZINA, 8 – 42016 – GUASTALL A (REG GIO E.
An important point after buying a device Bertazzoni CTYK..U7X(2,5)A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bertazzoni CTYK..U7X(2,5)A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bertazzoni CTYK..U7X(2,5)A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bertazzoni CTYK..U7X(2,5)A you will learn all the available features of the product, as well as information on its operation. The information that you get Bertazzoni CTYK..U7X(2,5)A will certainly help you make a decision on the purchase.
If you already are a holder of Bertazzoni CTYK..U7X(2,5)A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bertazzoni CTYK..U7X(2,5)A.
However, one of the most important roles played by the user manual is to help in solving problems with Bertazzoni CTYK..U7X(2,5)A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bertazzoni CTYK..U7X(2,5)A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
