Instruction/ maintenance manual of the product 700IDT Xenarc Technologies
Go to page of 8
700IDT In-dash Touchscr een VGA LCD Monitor Owner’s Records The model and serial numbers are located on the rear of the unit. Please record these numbers in the spaces provided below, as well as the dealer nam e, address, and telephone number. Please refer to these re cords when ever sp eakin g to your dealer regarding t his product .
2 NOTE NOTE 1: If you are trying to conn ect the mon itor to a laptop c omputer, pl ease make sure to enable the 15-Pin D- SUB exter nal monitor output located at the back of your laptop com puter. S ome laptop c omputers have three m odes: Lapt op Display Only, Laptop Displa y plus Exte rnal Monit or, and Ex ternal Monitor Only.
14 8. Click Finish to finish the installatio n . You will be asked to restart your computer. 9. Remove th e CD and Restart your computer . After Wind ows XP is finished loading, connect the 700 TS or 700TSV USB cable to one of your co mputer’s USB Ports.
4 7” In-Dash Touch Screen Monitor package contents 1. 7” In-Dash Touch Screen Monitor Main Unit 2. Trim Plate 3. Sleeve 700IDT Overview 1. Front View 1 2 3 13 4. Select the Rotating Monitor Utility and/ or the Shutdown Utility if you want to install them and click on Next to continue.
12 Connect signal source 1. Connect the 20-PIN connect or on the blac k monitor cable to the back of the 700IDT. Ro ute the cable th rough the das h to your PC. 2. Connect the D-Sub15 15-PIN VGA connect or to your c omputer’ s monitor output. 3. Connect the Yellow RCA p lug lab eled 1 and 2 to your comp o site video sources if required (e.
6 4. Swivel Left/Right 15 0 Swivel Left 15 0 Swivel right 15 0 - Hold the top of the monitor with both hands - Push and pull as illustrated - Hold the top of the monitor with both hands - Push and pul.
10 In-dash Monitor installation: 1. Remove the trim plate and sleeve 2. Install the sleeve into the dashboard 3. After the sleeve is correctly installed into the dashboard, bend the appropriate tabs to hold the sleeve firmly in place 4. Slide the main unit into the sleeve 5.
8 Default - Load default setting. AV2 First - Set whether to have monitor switch to Video Input 2 auto matically if a signal is present. Good for car reverse m onitoring system . Scaler - Set the display mode t o 16:9 or 4: 3. Set it to 4:3 if y our vide o signal is i n 4:3 aspect ratio a nd you don’t want the display to be stretched out.
An important point after buying a device Xenarc Technologies 700IDT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Xenarc Technologies 700IDT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Xenarc Technologies 700IDT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Xenarc Technologies 700IDT you will learn all the available features of the product, as well as information on its operation. The information that you get Xenarc Technologies 700IDT will certainly help you make a decision on the purchase.
If you already are a holder of Xenarc Technologies 700IDT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Xenarc Technologies 700IDT.
However, one of the most important roles played by the user manual is to help in solving problems with Xenarc Technologies 700IDT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Xenarc Technologies 700IDT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
