Instruction/ maintenance manual of the product Volume Controls Xantech
Go to page of 10
XVCD50 XVCD100 XVCD100IR XVCS50 XVCS100 XVCS100IR XVC50 XVC100 XVCO100 INST ALLA TION INSTRUCTIONS XANTECH VOLUME CONTROLS Installation Instructions XV Volume Controls Xantech’s premier product line of XV volume controls are in-wall mountable stereo speaker volu me control with impedance matching capability.
XVCD50 XVCD100 XVCD100IR XVCS50 XVCS100 XVCS100IR XVC50 XVC100 XVCO100 INST ALLA TION INSTRUCTIONS XANTECH VOLUME CONTROLS Installation Instructions XVC Series Volume Controls Xantech’s premier product line of XV volume controls are in-wall mountable stereo speaker volu me control with impedance matching capability.
Installation Requirements You will need at the very least, a ⅛ ” slotted screwdriver, a ¼” slotted screwdriver, wire cu tters and wire strippers. The recommended speaker wire to be used is 16-gauge stranded copper speaker wire. For runs longer than 100 feet, we recommend 14-gauge stranded copper speaker wire.
Installation Requirements You will need at the very least, a ⅛ ” slotted screwdriver, a ¼” slotted screwdriver, wire cu tters and wire strippers. The recommended speaker wire to be used is 16-gauge stranded copper speaker wire. For runs longer than 100 feet, we recommend 14-gauge stranded copper speaker wire.
Example 1: Two pairs of 8 Ohm ceiling s peakers are to be used with two volume controls, all driven by a single amplifier rated for 8 Ohm minimum safe operating load impedance. 1) Refer to “CHART A”, 8 Ohm Minimum Amplifier. 2) In the first colu mn, find “8 Ohms”.
CHART B: 4 Ohm M inimu m Ampl ifie r Example 1: Two pairs of 8 Ohm ceiling s peakers are to be used with two volume controls, all driven by a single amplifier rated for 8 Ohm minimum safe operating load impedance. 1) Refer to “CHART A”, 8 Ohm Minimum Amplifier.
Multiple Zone, Single Speaker Pair Volume Control Application Single Zone, Single Speaker Pair Volume Control and IR Receiver Application Note: Applies to Model XVCD100IR, XVCS100IR only 9 8 1 234567 .
Multiple Zone, Single Speaker Pair Volume Control Application Single Zone, Single Speaker Pair Volume Control and IR Receiver Application Note: Applies to Model XVCD100IR, XVCS100IR only 9 8 1 234567 .
CB18 Connecting Block (not included) The CB18 provides a convenient way to parallel many wires onto a 4 conductor bus. You can easily connect many home run leads from volume controls to the output terminals of a main amplifier. The CB18 features the following: - Nine 4-terminal plug-in connectors on a 4-conductor bus.
CB18 Connecting Block (not included) The CB18 provides a convenient way to parallel many wires onto a 4 conductor bus. You can easily connect many home run leads from volume controls to the output terminals of a main amplifier. The CB18 features the following: - Nine 4-terminal plug-in connectors on a 4-conductor bus.
An important point after buying a device Xantech Xantech Volume Controls (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Xantech Xantech Volume Controls yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Xantech Xantech Volume Controls - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Xantech Xantech Volume Controls you will learn all the available features of the product, as well as information on its operation. The information that you get Xantech Xantech Volume Controls will certainly help you make a decision on the purchase.
If you already are a holder of Xantech Xantech Volume Controls, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Xantech Xantech Volume Controls.
However, one of the most important roles played by the user manual is to help in solving problems with Xantech Xantech Volume Controls. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Xantech Xantech Volume Controls along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
