Instruction/ maintenance manual of the product HD88C Xantech
Go to page of 16
08905150B - 1 - INSTALLATION INSTRUCTIONS HD88CC5 HD88C High Definition Video Matrix Switcher, Coaxial and CAT5 High Definition Video Matrix Switcher, Coaxial Only DESCRIPTION The HD88CC5 eight-source.
08905150B - 2 - Safety Information CAUTION: TO REDUCE THE RISK OF ELECTRI C SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
08905150B - 3 - Damage Requiring Service — These appliances should be serviced by qualified service person nel when: • A power supply connection or a plug has be en dam aged or • If liquid has b.
08905150B - 4 - IMPORTANT NOTICE HD44 Series and HD88 Series INTRODUCTION In some installation scenarios, an audio/video source component (such as a cable box or DVD player) may fail to work properly with distribution pr oducts or even a display.
08905150B - 5 - DETAIL OVERVIEW FRONT PANEL The front panel is designed to provide the unit’s cu rrent Output/Input setting st atus. Note that only one Output/Input status setting is displayed at any given moment. The top row of LED indicators represents the current ZO NE output selection.
08905150B - 6 - REAR PANEL [1] SOURCE LOOP-THROUGH CONNECTION The source inputs are buffered to pr ovide an output at the same level as the input – i.e. Unity Gain (assuming a 75-ohm termination is on the output). Use these connections for HD88 expansion systems.
08905150B - 7 - [4] RS232 (SERIAL) COMMANDS The RS232 Port is bi-directional. The communica tion parameters are se t to 9600 Baud 8-N-1. DB9 CONNECTOR CIRCUIT PIN TX 2 RX 3 GND 5 RS232 COMMAND STRUCTURE Where: { z# } - Zone Number. Range is 1..4 (1..16 if expanded) { s# } - Source Input Number.
08905150B - 8 - [5] RS232 EXPANSION The HD88C and HD88CC5 can be exp anded into larger systems. By using any combination of the HD88C and HD88CC5 (up to 4 units), a larger High- Definition distribution syst em can be created for up to 32 Zones of Component Video and Digital Audio Distribution.
08905150B - 9 - [7] IR BUS The IR_IN port utilizes a 3. 5mm mono jack. Use this port to connect to an IR emitter ou tput port of a Xantech connecting block. PLUG CIRCUIT TIP IR SIGNAL SLEEVE GROUND [8] CAT5 ZONE OUTPUT This is an Output connection to the HDRXSG01 rece iver module.
08905150B - 10 - QUICK INSTALLATION: HD88CC5 and HDRXSG01 [1] Connect the High-Definition Source to the HD88CC5 or HDTXSG01. Figure 1 below shows an HD88CC5 (video matrix transmitter) c onnected to the HDRXSG01 (receiver). [2] Using CAT5 cable, connect the HD88CC5 zone output or the output from the HDTXSG01 to the HDRXSG01.
08905150B - 11 - RC68+ (IR) COMMANDS The RC68+ should be set to Group Code “F1”. ZONE 1 2 3 4 5 6 7 8 1 Zone Selec tion 80 48 10 90 00 C0 50 D0 2 Source Selection 40 A0 30 B0 20 E0 70 F0 3 Zone Po.
08905150B - 12 - ADVANCE INSTALLATION Sports Bar The figure below shows a diagram for a sports bar application. With the equipment rack located near or behind the bar area, the coaxia l outputs can be used for local HD monitors. The CAT5 outputs can be used to deliver HD content to areas such as outdoor patios and pool table recreational areas.
08905150B - 13 - Expanded System The figure below shows an expanded HD88CC5 (16 Z ones and up to 32 HD monitors) system. With two HD88CC5 devices, HD content can be distribut ed to 32 displays (16 with CAT5 outputs, 16 with coaxial outputs).
08905150B - 14 - Notes:.
08905150B - 15 - Xantech Limited Warranty (Effective for products sold after July 1, 2006) Xantech Corporation (“Xa ntech”) warrants to the holder of a valid proof of purcha se as the first end-us.
08905150B - 16 - Xantech Corporation 13100 Telfair Avenue Sylmar, CA 91342 www.xantech.com Phone: (818) 362-0353, Fax: (818) 36 2-9506 Installation Instructions, HD88CC5, HD88C © 2009 Xantech Corporation This document is copy righ t protected.
An important point after buying a device Xantech HD88C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Xantech HD88C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Xantech HD88C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Xantech HD88C you will learn all the available features of the product, as well as information on its operation. The information that you get Xantech HD88C will certainly help you make a decision on the purchase.
If you already are a holder of Xantech HD88C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Xantech HD88C.
However, one of the most important roles played by the user manual is to help in solving problems with Xantech HD88C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Xantech HD88C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
