Instruction/ maintenance manual of the product HD44C Xantech
Go to page of 12
08905071A - 1 - INSTALLATION INSTRUCTIONS HD44CC5 HD44C High Definition Video Matrix Switcher, Coaxial and CAT5 High Definition Video Matrix Switcher, Coaxial Only DESCRIPTION The HD44CC5 four-source, four-z one high-definition matrix swit cher has component video and S/PDIF digital audio inputs for each source.
08905071A - 2 - DETAIL OVERVIEW [1] SOURCE LOOP-THROUGH CONNECTION The source inputs are buffered to provide an output at the sa me levels, assuming a 75-ohm termination is on the output. Use these connections for HD44 expansion systems. The buffers are an active circuit.
08905071A - 3 - [3] IR RECEIVER The rear panel IR receiver is a 3.5mm Stereo jack t hat is compatible with all Xantech IR receivers, such as the 291-10. Switch 4 must be in the OFF position to use this jack. PLUG CIRCUIT TIP IR SIGNAL RING GROUND SLEEVE +12VDC, 25mA [4] IR BUS, EMITTER PORT The 3.
08905071A - 4 - RS232 QUERIES NAME QUERY RESPONSE EXAMPL E EXPLANATION Zone Power ?{ z# }PR+ ?{ z# }PR{ 0/1 }+ ?7PR0+ Power in zone 7 is OFF. Input Select ?{ z# }SS+ ?{ z# }SS{ s# }+ ?5SS3+ Zone 5 is Source 3. [6] AC POWER INPUT Standard IEC 3-Conductor AC Line Cord Receptacle fo r plug-in of a 3-conducator power line cord.
08905071A - 5 - [9] CAT5 ZONE OUTPUT Output connection to the HDRXSG01 receiver module. Uses standard CAT5 cable. Be sure to verify CAT5 wiring connection is correct before installation. [10] COAXIAL ZONE OUTPUT Gold-plated RCA jacks for connection to an HD moni tor.
08905071A - 6 - QUICK INSTALLATION: HD44CC5 and HDRXSG01 [1] Connect the High-Definition Source to the HD44CC5 or HDTXSG01. Figure 1 below shows a HD44CC5 (video matrix transmitter) c onnected to the HDRXSG01 (receiver). [2] Using CAT5 cable, connect the HD44CC5 zone output or the output from the HDTXSG01 to the HDRXSG01.
08905071A - 7 - RC68+ (IR) COMMANDS The RC68+ should be set to Group Code “C0”. ZONE 1 ZONE 2 ZONE 3 ZONE 4 1 Zone Power Toggle 80 48 10 90 SRC 1 SRC 2 SRC 3 SRC 4 Zone 1 Source Select 00 C0 50 D0.
08905071A - 8 - ADVANCE INSTALLATION FIGURE 2: Below shows a diagram for a sports bar app lication. With the equipment rack located near or behind the bar area, the coaxia l outputs can be used for local HD monitors. The CAT5 outputs can be used to deliver HD content to areas such as outdoor patios and pool table recreational areas.
08905071A - 9 - FIGURE 3.
.
.
08905071A - 10 - Xantech Corporation 13100 Telfair Avenue, 2/F Sylmar, CA 91342 www.xantech.com Phone: (818) 362-0353, Fax: (818) 36 2-9506 Installation Instructions, HD44CC5, HD44C © 2007 Xantech Corporation This document is copy righ t protected.
An important point after buying a device Xantech HD44C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Xantech HD44C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Xantech HD44C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Xantech HD44C you will learn all the available features of the product, as well as information on its operation. The information that you get Xantech HD44C will certainly help you make a decision on the purchase.
If you already are a holder of Xantech HD44C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Xantech HD44C.
However, one of the most important roles played by the user manual is to help in solving problems with Xantech HD44C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Xantech HD44C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
