Instruction/ maintenance manual of the product R Class Conversion to WES7 Wyse
Go to page of 18
Inst allation Guide Wyse ® R Class Conversion to WES7 Wyse ® USB Firmware T ool TM Release 1.10 Issue: 102910 PN: 883887-18L Rev . B.
Copyright Notices © 2010, Wyse T echnology Inc. All right s reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not rep roduce, transmit, transcribe, store i.
Content s 1 Introduction 1 Kit Contents 1 Overview 2 Wyse T echnical Support 2 Related Document ation and Services 2 Wyse Online Community 2 2 Inst alling R90L Thin Client Flash and RAM 3 Requirements.
iv Contents This page intentionally blank..
1 Introduction This guide provides ste p-by-step in structions to c onvert R90L thin clients from XPe to WES7. Caution WES7 firmware requires R class thin clients to h ave a minimum of 4 GB fla sh and 2 GB RAM. Tip After conv erting your thin clie nts, obtain a ny available firmwar e update a t http://www .
2 Chapter 1 The Conversion Sof tware Assembly DVD-ROM conta ins: • A PDF of this Reference Guide • Wyse USB Firmware T ool Release 1.10 • R Class WES7 Conversion Ima ge folder contain ing the following files: · bios.img · cmos.img · commandsXml.
2 Inst alling R90L Thin Client Flash and RAM This chapter cont ains information for users of Wyse R90L thin client s who must install new flash and RAM. If you are inst alling firmware only , you can sk ip this chapte r and proceed to"Installing WES7 Firmware.
4 Chapter 2 Procedures S tep 1: Remove the R90L Thin Client Left Side Cover Caution Follow all precautions listed in the Quick- S tart Guide that came with your thin client for disconne cting and reconnecting the thin client.
Installing R90L Thin Client Flash and RAM 5 S tep 2: Install the R90L Flash Module Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD).
6 Chapter 2 S tep 3: Install the R90L RAM Module Wa r n i n g RAM modules may be susceptible to damage by Electro-S t atic Discharge (ESD). All industry-st andard cautions should be fo llowed to avoid ESD.
3 Inst alling WES7 Firmware This chapter include s the requirement s and procedures you nee d to install and use Wyse ® USB Firmware T ool TM to update your thin c lient to WE S7 firmware.
8 Chapter 3 S tep 3: Use Wyse USB Firmware T ool to Config ure a Single USB Key to Inst all Firmware 1. Double-click the shortcu t to run the tool an d open the Wyse USB Firmware T o ol wizard (the welcome p age provides the p roduct version and descriptio n, and a link to view the Wyse end user license agreemen t).
Installing WES7 Firmware 9 4. Select the Windows Embedded S t andard 7 OS type o ption. 5. Select the Up date Firmware operation to perform optio n. Tip Although the Preserve dat a p artition check bo.
10 Chapter 3 Figure 12 Prep are USB drive 11 . Select the USB key onto which you want the configurations (you can use Refresh as needed to recogn ize an inserted USB key), and then click Next . The pr ogress bar s show the ov erall prog ress and task pr ogress.
Installing WES7 Firmware 11 S tep 5: V erifying Thin Client Operation After the thin client reboo ts, you can ver ify the Ve r s i o n and that your general client information is cor rect.
12 Chapter 3 S tep 6: Attach a Wyse Conversion Label and Microso ft License Label on Each Converted Thin Client The conversion kit is suppl ied with Wyse Conversion Labels and Microsof t License Labels that must be atta ched to each thin client as shown in Figure 14.
Installing WES7 Firmware 13 T roubleshooting This section contains ge neral troubleshooting information . USB Keys - T roubleshoot ing Boot Issues Due to differ ent manufacturing proce sses on U SB keys (and the variety of them), not all brands have been tested with the Wyse USB Firmware T ool.
Inst allation Guide Wys e ® R Class Conversion to WES7 Issue: 1029 10 Written and publishe d by: Wyse T echnology Inc., October 2010 Created using FrameMake r ® and Acrobat ®.
An important point after buying a device Wyse R Class Conversion to WES7 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wyse R Class Conversion to WES7 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wyse R Class Conversion to WES7 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wyse R Class Conversion to WES7 you will learn all the available features of the product, as well as information on its operation. The information that you get Wyse R Class Conversion to WES7 will certainly help you make a decision on the purchase.
If you already are a holder of Wyse R Class Conversion to WES7, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wyse R Class Conversion to WES7.
However, one of the most important roles played by the user manual is to help in solving problems with Wyse R Class Conversion to WES7. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wyse R Class Conversion to WES7 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
