Instruction/ maintenance manual of the product 1002899 Woods Equipment
Go to page of 22
I NST AL LA TION MAN U AL SA VE THIS MANU AL! Include it with the backhoe manual. It contains safety , operation, and repair part information not found in other manuals.
2 Introduction SFMK (Rev . 6/6/2005) T O THE DEALER : Assemb ly and prop er installati on of this product is the respons ibility of the Woods ® dea ler .
Safety 3 4-Point SFMK (Rev . 7/8/2005) S AFETY RULE S ATTENTION! BECOME ALER T! YOUR SAFETY IS IN V OLVED! This Sub-Frame Mounting Kit is only fo r the backhoes and tractors specified in the Su b-Frame Mount Installation secti on of this manua l. Any other use or modi fication of this m ountin g kit may result in se rious injury or deat h.
4 Safety 4-Po int S FMK (Rev . 7/ 8/ 200 5) SAFETY RULES ATTENTION! BECOME ALER T! YOUR SAFETY IS IN V OLV ED! (Safety R ules co ntinued from previous page) Always wear relatively tight and belted clothing to avoid getting caught in moving p arts.
Inst allation 5 MAN013 1 (Rev . 12/23/200 5) BACKHOE SUB-FRAME INST ALLA TION T ractor Prep aration ■ Only us e 10028 99 Sub -Fram e Mountin g Ki t for mounting Woo ds BH6500 Backhoes on Cub Cadet ® 7000, 71 92, 7194, 71 95, 7200, 7205 tr actors and Mahindra 2015 t r actors equipped with W oods 1006, Cub Cad et 475, or Mahin dra ML104 L oaders.
6 Installation MAN01 31 (Rev . 12/23 /2005) Inst all Rear M ounting Bracket Refer to Figure 2. 1. Positio n rear mo unting brac ket (2) o n tractor ax le housings (D). 2. Install cap screws (9) and ha rdened fl at washers (8) in top two hol es of m ountin g br acket ( 2) as shown.
Inst allation 7 MAN013 1 (Rev . 12/23/200 5) Sub-Frame Fit-Up Refer to Figure 4. 1. Cen ter sub- frame un der tracto r . 2. Ins ert cr oss tu be of su b-frame into ch annel o f rear mount brac ket (2). 3. Se cure in pl ace with c levis pins (6 ) and kl ik pin (7).
8 Installation MAN01 31 (Rev . 12/23 /2005) HYDRAULIC INST ALLA TION Keep hands and body away from pressurized lin es. Use p ape r or card boar d, not ha nds or o ther body part s to ch eck fo r leaks. Wear safety goggle s. Hydraulic fluid under pressure can easily penetrate skin and will c ause serious injury or death.
Inst allation 9 MAN013 1 (Rev . 12/23/200 5) 100289 8 HOSE KIT INST ALLATION Completion of this hose kit requires connection to the trac tor hydraulic manifold and loader control valve. Shut off engine and lock p a rking brake be fore inst alling hose kit.
10 Installation MAN01 31 (Rev . 12/23 /2005) W OODS 1006 LOADER Inst all Hydraulic Fittings Use threa d sealant on pipe threads. Be ca reful not t o use exces s sea lant that c ould enter hyd raulic system . NOTE: Some fittin gs in hose k it will not be used for this installa tion.
Inst allation 11 MAN013 1 (Rev . 12/23/200 5) MAHINDRA ML104 LOA DER Inst all Hydraulic Fittings Use thre ad sealan t on pipe thr eads. Be care ful not t o use exce ss se alant t hat could enter hydraulic system . NOTE: Some fi ttings in ho se kit will not be use d for this installa tion.
12 Installation MAN01 31 (Rev . 12/23 /2005) CUB CADET 475 LOA DER Remove Hy draulic Fittings Use threa d sealant on pipe threads. Be ca reful not t o use exces s sea lant that c ould enter hyd raulic system . NOTE: Some fittin gs in hose k it will not be used for this installa tion.
Inst allation 13 MAN013 1 (Rev . 12/23/200 5) Inst all PBY T ube Assembly 1. Remove s lug on righ t side of b ackhoe c onsole. 2. Remove pl ug from PBY port on r ight si de of b ack- hoe valv e. 3. Install Po wer Bey ond s leeve ( 10), s traight con- nector (12) , and tu be assemb ly (1 1) on the si de of the back hoe va lve PBY port.
14 Installation MAN01 31 (Rev . 12/23 /2005) Backhoe and Loader Hose Connections 1. Attach ho se (A) fro m the loader v alv e OUT p ort t o female quick cou pler (2) in the front o f tee ( 5). 2. Connect hos e (B) from the lo ader valv e PBY por t to male q uick coupler in t he PBY p ort ( N) on th e hydraulic mani fold.
Inst allation 15 MAN013 1 (Rev . 12/23/200 5) Mount Sub-Frame & Ba ckhoe to T racto r This mounting kit is designed to provide secure moun ting and adequ ate operator c lear- ance when properly inst alled. Check clearance dimen sions shown b elo w to be s ure you h ave installed seat bra cket co rrect ly .
16 Installation MAN01 31 (Rev . 12/23 /2005) Remove Backhoe With Sub-Frame The only time the bac khoe may be operated from a position other than the operator seat is during backhoe a tt ach ment and rem oval. Opera- tor must: • Read Mounting Kit Manual instructions on att aching and removing backhoe and use extreme c are.
Part s 17 MAN013 1 (Rev . 12/23/200 5) 1002899 SUB-FRA ME MOUNTING KIT 14 15 13 10 11 12 9 8 7 6 5 3 4 2 1 3 17 11 19 18 16 20 10 For Mahindra ML104 Loader Mount CD5017B Seria l Number Pl ate Located inside sub-fram e side rail, rear of cross tub e MODEL NO.
18 Part s MAN0131 (Rev .12/23/2005 ) 1002898 HOSE KIT 9 1 2 2 4 2 7 6 3 5 4 8 1 2 P T N 3 4 Hose Connection with Cub Cadet 475 Loader Hose Connection with Woods 1006 Loader or Mahindra ML104 Loader P .
Appendix 19 Bolt T orque & Siz e Chart s (Rev . 10/10/ 2005) BOLT T OR QUE CHA R T Always tighten har dware to these values unles s a di ff e rent t orque value or tighteni ng pro cedure is list ed for a specifi c applica tio n. F ast eners must alwa y s be re placed wi th the s ame grade as spec ified in the manual par ts list.
20 Appendix Bolt T orque & Siz e Charts (Rev . 10/10/2 005) BOLT SIZE CHART NO TE: Char t shows bo lt thread sizes and corres ponding h ead ( wrench) sizes for standard SAE and metr ic bol ts. ABBREVIATIONS A G ................... ............. ..
F-3079 (Rev . 9/21/2005) Wo od s Eq u ip m e n t Company 260 6 South Illinois Ro ute 2 Post Offi ce Box 1000 Oregon, Illinois 61061 815- 7 32-2141 tel 815- 7 32- 7580 fax www .
F-8494 (Rev . 6/23/2005) W oods Equipm ent Company 260 6 South Illinois Route 2 Post Office Box 1000 Oregon, Illinoi s 610 61 815- 73 2-2141 tel 815- 73 2- 75 80 fax www .W oodsEquipme nt.com ©2001 Woods Equipment Company . All rights reserved. WOO DS, the Woods logo, and "T ested.
An important point after buying a device Woods Equipment 1002899 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Woods Equipment 1002899 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Woods Equipment 1002899 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Woods Equipment 1002899 you will learn all the available features of the product, as well as information on its operation. The information that you get Woods Equipment 1002899 will certainly help you make a decision on the purchase.
If you already are a holder of Woods Equipment 1002899, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Woods Equipment 1002899.
However, one of the most important roles played by the user manual is to help in solving problems with Woods Equipment 1002899. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Woods Equipment 1002899 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
