Instruction/ maintenance manual of the product Ventilation Hood Wolf
Go to page of 16
I NST ALLA TION I NSTR UCTIONS C OOKT OP V ENTILA TION H OODS.
As you follow these instructions, you will notice W ARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equip- ment. There are two types of potential hazards that may occur during installation.
3 INST ALLA TION REQUIREMENTS IMPORT ANT NOTE: This installation must be completed by a qualified installer or W olf a uthorized service center technician. I nstaller: P lease read the entire Installation Instructions prior to installation. Save these instructions for the local inspector’ s refer- e nce, then leave them with the homeowner .
O VERALL DIMENSIONS MODEL CTWH30 Overall Width 30" (762) O verall Height (excluding chimney) 6 7 / 8 " (175) O verall Height (including chimney) 3 0 1 / 2 " (775) Max Height (full extension) 48 1 / 2 " (1232) Overall Depth 21" (533) Shipping W eight (shell only) 85 lbs (39 kg) Dimensions may vary to + – 1 / 8 " (3).
HOOD PLA CEMENT W olf cooktop wall and island hoods come with a telescopic chimney flue that allows you to r each a ceiling height of 8' (2.4 m) to 9' (2.7 m) with a finished look. A flue extension to accommodate 10' (3 m) ceilings is available.
W ALL HOOD INST ALLA TION INST ALL DUCTWORK IMPORT ANT NOTE: Consult a qualified HV AC Engineer for specific ducting applications. Decide where the ductwork will run between the hood and the outside. A straight, short duct run will allow the hood to perform more efficiently .
7 INST ALLA TION INSTRUCTIONS W ALL HOOD INST ALLA TION ELECTRICAL REQUIREMENTS W olf cooktop wall hoods require a separate, grounded 110 / 120 V AC, 60 Hz power supply .
CONNECT DUCTW ORK U se the screws and wall anchors provided to secure the upper brackets to the ceiling. Position the upper brackets based on the d imension of the telescopic chimney flue. Use an 8" (203) round metal duct to connect the duct collar on the hood to the ductwork above.
9 Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION INSTRUCTIONS ISLAND HOOD INST ALLA TION INST ALL DUCTWORK IMPORT ANT NOTE: Consult a qualified HV AC Engineer for specific ducting applications. Decide where the ductwork will run between the hood and the outside.
10 W OLF COOKT OP VENTILA TION HOODS Secure the upper half of the support frame to the joists and cross framing with four screws p rovided with your hood. Make sure that the screws are driven into the center of the joists and framing for maximum strength.
11 Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION INSTRUCTIONS ISLAND HOOD INST ALLA TION MOUNT HOOD T O SUPPOR T FRAME M ount the hood to the support frame by aligning the four weld screws on the hood to the four holes on the support frame.
12 Dimensions in parentheses are in millimeters unless otherwise specified. W OLF COOKT OP VENTILA TION HOODS A CCESSORIES Optional acces- sories are available through your Wolf dealer . T o obtain local dealer information, visit the Locator section of our website, wolfappliance.
13 INST ALLA TION INSTRUCTIONS INTERNAL BLO WERS INTERNAL BLO WER INST ALLA TION I MPORT ANT NOTE: F or mounting and installation of the internal blower , refer to the specific installation instructions provided with e ach blower . 1) Remove the hood filters.
14 W OLF COOKT OP VENTILA TION HOODS IMPORT ANT NOTE: Before turning the power on to the ventilation hood, make sure the b lower is in the OFF position.
15 CONT ACT I NFORMA TION Wolf Customer Service: 800-332-9513 Website: wolfappliance.com TROUBLE SHOO TING IMPORT ANT NOTE: If the cooktop ventilation hood does not operate properly , follow these t roubleshooting steps: V erify that power is being supplied to the ventilation hood.
807574 9 / 2005 WOLF APPLIANCE COMP ANY , LLC P . O . BOX 44848 MADISON, WI 53744 800-332-9513 WOLF APPLIANCE.COM.
An important point after buying a device Wolf Ventilation Hood (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wolf Ventilation Hood yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wolf Ventilation Hood - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wolf Ventilation Hood you will learn all the available features of the product, as well as information on its operation. The information that you get Wolf Ventilation Hood will certainly help you make a decision on the purchase.
If you already are a holder of Wolf Ventilation Hood, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wolf Ventilation Hood.
However, one of the most important roles played by the user manual is to help in solving problems with Wolf Ventilation Hood. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wolf Ventilation Hood along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
