Instruction/ maintenance manual of the product LB2000 Windsor
Go to page of 28
HIGH SPEED BURNISHER Operating Instructions (ENG) MODELS: LB2000 980088 11/15/03 C Read these instructions before using the machine.
MACHINE DATA LOG/OVERVIEW LB2000 980088 03/08/03 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: _______________________________________________________________.
TABLE OF CONTENTS LB2000 980088 03/08/03 3 Machine Data Log/Overview. ......................... 2 Table of Contents ........................................... 3 HOW TO USE THIS MANUAL How to use this Manual. ................................ 1 - 1 SAFETY Important Safety Instructions .
HOW TO USE THIS MANUAL LB2000 980088 03/08/03 1 - 1 This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
LB2000 9800 88 03/08/03 2 - 1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only ind oors.
HAZARD INTENSITY LEVEL LB2000 980088 03/08/03 2 - 2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY.
GROUNDING INSTRUCTIONS LB2000 980088 03/08/03 2 - 3 THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine.
TECHNICAL SPECIFICATIONS LB2000 980088 03/08/03 3 - 1 ITEM DIMENSION/CAPACITY Construction Heavy - duty die cast aluminum deck with heavy - duty rubber bumper, tubular steel self adjusting handle with die cast aluminum handle housing. Motor 1.75 hp Transmission Direct drive from motor shaft.
HANDLE INSTALLATION LB2000 980088 03/08/03 3 - 2 4. Slide Bolt (item 3) thru, washers (item 2), Handle Mount Brackets and Handle Assembly as shown. Tighten bolt (item 3) and nut (item 1) until the handle can not twist in the mount bracket (45 - 50 foot pounds).
OPERATION LB2000 980088 03/08/03 3 - 3 ! CAUTION CONTROLS 1. Safety Lock – Prevents unintended operation of the machine. 2. Switch Levers – Turns machine on/off. OPERATION For indoor use only. When using the pad, always keep the machine moving when in contact with the floor.
MACHINE TROUBLESHOOTING LB2000 980088 03/08/03 4 - 1 PROBLEM CAUSE SOLUTION Machine will not run Tripped circuit breaker Reset Circuit breaker tripped in building. Check and reset Fuse in motor is blown Replace CAUTION: To reduce the risk of electrical shock, unplug the machine before opening fuse holder.
WIRING DIAGRAM / SERVICE SCHEDULE LB2000 980088 11/15/03 4 - 2 SERVICE SCHEDULE MAINTENANCE DAILY MONTHLY Check pad wear to prevent buildup of chemicals * Check pad driver system for damage * Check ha.
LB2000 980088 03/08/03 4 - 3 THIS PAGE LEFT BLANK INTENTIONALLY.
DECK GROUP LB2000 980088 03/08/03 5 - 1 16 8 11 13 14 15 12 9 10 6 7 1 4 5 3 2.
DECK GROUP LB2000 980088 03/08/03 5 - 2 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 140449 4 BUMPER, RUBBER 2 27918 1 COVER, FILTER BAG 3 140441 1 BAG, DUST (PACKAGE OF 10 BAGS) 4 67463 1 RETAINER, CORD 5 70738 2 SCR, M5 X .
HANDLE GROUP LB2000 980088 03/08/03 5 - 3 16 17 1 2 3 4 5 6 10 7 9 8 11 15 14 13 12.
HANDLE GROUP LB2000 980088 03/08/03 5 - 4 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 70686 2 SCR, M6 X 45 SHCS BLK 2 51326 1 LOCK, SAFETY HANDLE 3 73990 2 SPRING, EXT.
LOWER HANDLE GROUP LB2000 980088 03/08/03 5 - 5 20 8 21 19 22 23 8 24 4 5 10 18 17 13 8 16 15 14 6 8 11 9 7 21 20 12 1 2 3.
LOWER HANDLE GROUP LB2000 980088 03/08/03 5 - 6 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 70738 1 SCR, M5 X .8MM X 10 MM PPHMS BLK 2 20005 1 CLAMP, 5/16 NYLON 3 67468 2 RING, 10MM EXTERNAL.
MOTOR GROUP LB2000 980088 03/08/03 5 - 7 1 2 3.
MOTOR GROUP LB2000 980088 10/17/03 5 - 8 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 70702 3 SCR, M5 X .8 X15MM BLK 2 27884 1 COVER, MOTOR 3 53256 1 MOTOR, 115VOLT 1.5HP 2000RPM INCLUDES ITEM 1 & 2 MOTOR COMPONENTS (NOT SHOWN) PART NO. QTY DESCRIPTION SERIAL NO.
PAD/DRIVER GROUP LB2000 980088 03/08/03 5 - 9 10 2 9 8 6 5 7 3 1 2 11 4 12.
PAD/DRIVER GROUP LB2000 980088 03/08/03 5 - 10 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 87163 4 WASHER, 3/8 SPLIT LOCK PLTD 2 70507 8 SCR, 3/8 - 16 X 3/4 HHCS PLT 3 87086 4 WASHER, M10 X .
WIRING GROUP LB2000 980088 11/15/03 5 - 11 11 8 9 6 2 1 3 4 10 9 8 5 7 12 PRIOR TO SN*.
WIRING GROUP LB2000 980088 11/15/03 5 - 12 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 70801 2 SCR, M3.5 X 40 PHTF TYPE B * WAS 70688 2 87057 2 WASHER, M4 SHAKEPROOF 3 73993 1 SPRING, COMP, .
SUGGESTED SPARE PARTS LB2000 980088 03 /08/03 5 - 13 PART NO. DESCRIPTION SERIAL NO. FROM NOTES: 73990 SPRING, EXT .5 OD X 3.5 L 73993 SPRING, COMP .48 OD X .
Windsor Industries reserves the right to change its w arrant y polic y w i th o ut n o tice – Rev2 10/16/02 1 WINDSOR INDUSTRI ES New M a chine Wa rrant y Limited Warranty Windsor Indu stries, Inc. warrants new machines a gain st de f ects in material and w orkmanship under norm al use and service to t he original purchaser.
Windsor Industries reserves the right to change its w arrant y polic y w i th o ut n o tice – Rev2 10/16/02 2 WINDSOR INDUSTRI ES New M a chine Wa rrant y 90 Day Warranty Ex tension Available Upon r.
An important point after buying a device Windsor LB2000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Windsor LB2000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Windsor LB2000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Windsor LB2000 you will learn all the available features of the product, as well as information on its operation. The information that you get Windsor LB2000 will certainly help you make a decision on the purchase.
If you already are a holder of Windsor LB2000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Windsor LB2000.
However, one of the most important roles played by the user manual is to help in solving problems with Windsor LB2000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Windsor LB2000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
