Instruction/ maintenance manual of the product SST White Rodgers
Go to page of 32
SST1000 SST1000 SST1000 SST1000 SST1000 SST1400 SST1400 SST1400 SST1400 SST1400 SST1600 SST1600 SST1600 SST1600 SST1600 SST2000 SST2000 SST2000 SST2000 SST2000 W H IT E -R O D G E R S O P ER A TIN G L.
2 DID YOU GET THE RIGHT SIZE DID YOU GET THE RIGHT SIZE DID YOU GET THE RIGHT SIZE DID YOU GET THE RIGHT SIZE DID YOU GET THE RIGHT SIZE AIR CLEANER AIR CLEANER AIR CLEANER AIR CLEANER AIR CLEANER Mod.
3 AB C Dir ty Air In Clean Air Out Cabinet Pre-Filters Handle Contact Button Contact Button Collecting Cells P ow er P ack HOW THE AIR CLEANER WORKS HOW THE AIR CLEANER WORKS HOW THE AIR CLEANER WORKS.
4 Air Flow Furnace Opening Not to Exceed 20 Air Flow Electronic Air Cleaner Opening Electronic Air Cleaner Furnace T ransition Section (if Needed) Figure 3 Cabinet (Interchangeable) Collecting Cell (I.
5 At Least 9 Inches Less than 7 Inches Offset Figure 10 Air Flow Figure 9 HIGHBOY FURNACE HIGHBOY FURNACE HIGHBOY FURNACE HIGHBOY FURNACE HIGHBOY FURNACE (Figure 9) (Figure 9) (Figure 9) (Figure 9) (Figure 9) Installation beneath furnace. Cleaner mounts horizontally, where return air enters from below.
6 Figure 12 Figure 13 Duct F rame Pow e r Supply Bo x Mounting Holes Air Flow T ur ning V anes Figure 14 Optional method (Bend tabs outward at 90˚ angle) Figure 15 REMOVE OLD FILTER AND DISCARD REMOV.
7 V er tical Section W ood Block T ape All Joints Figure 16 Hot Neutral Grounding Conductor F ront View Figure 17 Floor Conduit Duct Electronic Air Cleaner Figure 18 Cabinet Pre-Filters Handle Contact Button Contact Button Collecting Cells P ow er P ack Figure 19 7.
8 Operating Light On-Off Switch Figure 20 1. With the 120 VAC power turned on at the circuit breaker for the furnace, push the air cleaner ON-OFF switch to the “ON” position (Figure 20). 2. With the furnace blower running, the air cleaner will be operating.
9 REPLACING AN IONIZING WIRE REPLACING AN IONIZING WIRE REPLACING AN IONIZING WIRE REPLACING AN IONIZING WIRE REPLACING AN IONIZING WIRE If an ionizing wire should break, it can be replaced as follows: 1. Remove all pieces of broken wire. Make sure sup- ports at each end are in good condition and not bent out of shape.
10 SERVICE INDICATION SERVICE INDICATION SERVICE INDICATION SERVICE INDICATION SERVICE INDICATION SERVICE CHECKS SERVICE CHECKS SERVICE CHECKS SERVICE CHECKS SERVICE CHECKS ON/OFF switch “ON” Unit.
11 TECHNICAL REPAIR GUIDE TECHNICAL REPAIR GUIDE TECHNICAL REPAIR GUIDE TECHNICAL REPAIR GUIDE TECHNICAL REPAIR GUIDE The solid-state pow er supply is not designed f or individual component par t replacement and must be replaced as a complete "snap-in" unit.
12 POWER SUPPLY POWER SUPPLY POWER SUPPLY POWER SUPPLY POWER SUPPLY CHECKOUT PROCEDURE CHECKOUT PROCEDURE CHECKOUT PROCEDURE CHECKOUT PROCEDURE CHECKOUT PROCEDURE 1. Turn power switch to the “OFF” position and remove the power pack from cabinet. 2.
13 OZONE REDUCTION OZONE REDUCTION OZONE REDUCTION OZONE REDUCTION OZONE REDUCTION All electronic air cleaners typically produce a small amount of ozone that is within established limits. Some customers may notice an odor especially at high altitudes or low air flow rates.
14 1 2 3 4 5 5 6 2 3 7 8 9 18 5 14 13 10 11 12 REPAIR PARTS REPAIR PARTS REPAIR PARTS REPAIR PARTS REPAIR PARTS.
15 ITEM NO . DESCRIPTION P ART NUMBER SST1000 SST1400 SST1600 SST2000 1 Cabinet N/A N/A N/A N/A 2 Pre-Filter • F825-0431 • F825-0432 • F825-0337 • F825-0338 3 Collecting Cell • F811-0398 •.
NOTICE TO CONSUMERS White-Rodgers Electronic Air Cleaner Dear Consumer; White-Rodgers would like to thank you for purchasing a White-Rodgers Electronic Air Cleaner or product containing a White-Rodgers Electronic Air Cleaner.
Prière de lire attentivement le manuel avant d’installer l’appareil, de le mettre Prière de lire attentivement le manuel avant d’installer l’appareil, de le mettre Prière de lire attentivem.
2 ATTENTION ATTENTION ATTENTION ATTENTION ATTENTION MISE EN GARDE MISE EN GARDE MISE EN GARDE MISE EN GARDE MISE EN GARDE MISE EN GARDE MISE EN GARDE MISE EN GARDE MISE EN GARDE MISE EN GARDE DIRECTIV.
3 AB C Entr é e d ’ air poussi é reux Sortie d ’ air propre Bo î tier Pr é filtres Poign é e Bouton de contact Cellules collectrices Module d ’ alimentation Bouton de contact Figure 1 Figur.
4 É coulement de l ’ air Ouverture du g é n é rateur Ne pas d é passer 20 ° É coulement de l ’ air Ouverture du filtre à air é lectronique Filtre à air é lectronique G é n é rateur Sec.
5 Au moins 23 cm (9 po) Moins de 18 cm (7 po) Coude Figure 10 É coulement de l ’ air Figure 9 É coulement de l ’ air Figure 1 1 É coulement de l ’ air V ue de l ’ arri è re Figure 6 É cou.
6 Figure 12 Figure 13 Conduit Châssis T rous de montage Bo î te de raccordement É coulement de l ’ air Aubes directionnelles Figure 14 Autre m é thode (plier les pattes à 90 ° ) Figure 15 DÉM.
7 L’installation de l’appareil doit respecter les codes électri- L’installation de l’appareil doit respecter les codes électri- L’installation de l’appareil doit respecter les codes éle.
8 V oyant de marche Interrupteur Figure 20 EXPLOIT A TION 1. S’assurer que le générateur d’air chaud est alimenté en courant de 120 V C.A. Placer l’interrupteur du filtre à air à la position MARCHE (ON) (figure 20). 2. Le filtre à air fonctionnera lorsque le ventilateur du système de chauffage est en marche.
9 Support Fil ionisant Figure 21 Capacit é nominale 600 à 1 200 pi 3 /min 1 000 à 1 600 pi 3 /min 1 000 à 2 000 pi 3 /min 1 600 à 2 200 pi 3 /min Chute de pression maxi.
10 GUIDE DE RÉVISION DE B GUIDE DE RÉVISION DE B GUIDE DE RÉVISION DE B GUIDE DE RÉVISION DE B GUIDE DE RÉVISION DE B ASE SST ASE SST ASE SST ASE SST ASE SST Ce guide répond à la plupart des questions des propriétaires.
11 Ne pas tenter de réparer l’appareil avant de s’être complè- Ne pas tenter de réparer l’appareil avant de s’être complè- Ne pas tenter de réparer l’appareil avant de s’être compl.
12 PROCÉ PROCÉ PROCÉ PROCÉ PROCÉ D D D D D URE DE RÉVISION DU URE DE RÉVISION DU URE DE RÉVISION DU URE DE RÉVISION DU URE DE RÉVISION DU MODULE D’ALIMENTATION MODULE D’ALIMENTATION MODULE D’ALIMENTATION MODULE D’ALIMENTATION MODULE D’ALIMENTATION 1.
13 Ca Ca Ca Ca Ca v v v v v alier réducteur d’o alier réducteur d’o alier réducteur d’o alier réducteur d’o alier réducteur d’o z z z z z one one one one one Figure 24 LINE WHT/BRN BLK .
14 1 2 3 4 5 5 6 2 3 7 8 9 18 5 14 13 10 11 12 PIÈCES DE RECHANGE.
15 REP È RE DESCRIPTION NUM É RO DE PI È CE SST1000 SST1400 SST1600 SST2000 1 Bo î tier S.O. S.O. S.O. S.O. 2 Pr é filtre • F825-0431 • F825-0432 • F825-0337 • F825-0338 3 Cellule collect.
Le logo Emerson est une marque de commerce et une marque de service d ’ Emerson Electric Co. RAPPEL DE LAVAGE RAPPEL DE LAVAGE RAPPEL DE LAVAGE RAPPEL DE LAVAGE RAPPEL DE LAVAGE Le lavage régulier est essentiel pour assurer le rendement optimal de l’appareil.
An important point after buying a device White Rodgers SST (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought White Rodgers SST yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data White Rodgers SST - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, White Rodgers SST you will learn all the available features of the product, as well as information on its operation. The information that you get White Rodgers SST will certainly help you make a decision on the purchase.
If you already are a holder of White Rodgers SST, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime White Rodgers SST.
However, one of the most important roles played by the user manual is to help in solving problems with White Rodgers SST. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device White Rodgers SST along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
