Instruction/ maintenance manual of the product 414 White
Go to page of 20
IMPOR TANT: READ SAFETY RULES AND INSTRUCTIONS CAREFUL LY REAR TINE TILLER Model 414 PRINTED IN U.S.A. FORM NO. 770-10183 (10/98) O PER AT OR’S M AN UAL Warning: This unit is equipped with an intern.
2 SECTION 1: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new tiller. It will help you assemble, prepare and maintain your tiller.
3 SECTION 3: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR TILLER.
4 • Only use accessories approved for this machine by the manufacturer. Read, understand, and follow all instructions provided with the approved accessory. • If situations occur which are not covered by this manual, use care and good judgment. Contact your dealer for assistance.
5 SECTION 4: UNPACKING TO REM OVE UNIT FROM CARTON 1. Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton. 2. Remove loose parts included with unit (i.e., owner’s manual, etc.). 3. Cut along dotted lines and lay carton down flat.
6 Figure 4 3. Lift up the handle assembly and align the bottom holes in the handle assembly with the holes in the pivot bracket. Insert hex bolt (with Hex nut retainer attached through the round hole). The head of hex bolt and retainer bracket should be to the right hand side of the unit.
7 Figure 9 2. Slip the wire up through the slot on the cable bracket underneath the handle. Push the end of the casing up through the cable bracket. Rethread the hex nut on the end of the cable. Do not tighten at this time. Figure 10 Viewed beneath handle panel.
8 SECTION 6: CONTROLS Figure 11 GEAR SELECTION HANDLE The gear selection handle is located on the front of the handle assembly. It is used to select NEUTRAL, REVERSE, or one of the FORWARD modes. This tiller is designed for the gear selection handle to be moved while the engine is running.
9 5. Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle. 6. Repeat steps 4 and 5 until engine starts. 7. As engine warms up and begins to operate evenly, move choke lever gradually to RUN position.
10 4. Squeeze the clutch handle against the handle to engage the wheels and tines. NOTE: Make certain the gear selection indicator is correctly positioned before engaging the clutch handle. If it is between gears, the engine will stall. To transport tiller, do not engage the tines.
11 Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air circulation which is essential to engine performance and life. Be certain to remove all dirt and combustible debris from muffler area.
12 SECTION 12: TROUBLE SHOOTING GUIDE Note: For repairs beyond the minor adjustments above, contact your local authorized service dealer. Tr ouble Possible Cause(s) Corrective Action Engine fails to start Fuel tank empt y , or stale fuel. Throttle control lever not in correct starting position (if so equipped).
13 Notes.
14 Model 414.
15 Model 414 RE F . NO. PART NO DESCRIPTION 1 735-0246 Vinyl End Plug 2 647-0014 Clutch Control Ass’ y . 3 710-1017 T orx Mach. AB- T ap Sc r. 1/4 x .62" 4 786-0131 Handle Cover 5 786-0098 Retaining Brkt.—R.H. 6 786-0118 Retaining Brkt.—L.H.
16 Model 414 RE F . NO. PART NO. DESCRIPTION 1 710-3008 Hex Bolt 5/16-18 x .75" Lg. 2 712-3004A Hex T op L-Nut 5/16-18 Thd. 3 786-0107 Cable Mtg. Bracket 4 710-1017 T orx Mach. AB- Tap Scr. 1/4 x .6" Lg 5 738-0899 Belt Cover Bolt 6 786-0117 Shift Cover Bracket 7 786-0100 Belt Cover 8 736-0142 Fl-Wash.
17 Models 414 RE F . NO. PART NO. DESCRIPTION 1 721-0295 Chain Case Gasket 2 786-0086 Reinforcement Plate 3 716-0865 Snap Ring 4 750-0938 Spacer .735" I. D . x .886" O. D . 5 611-0058 Wheel Shaft 6 717-1458 Spur Gear 46T 8 736-0351 Fl-Wash. .
18.
19.
MANU FA CTURER’S LIMITED WARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, White Outdoor Products Company will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
An important point after buying a device White 414 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought White 414 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data White 414 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, White 414 you will learn all the available features of the product, as well as information on its operation. The information that you get White 414 will certainly help you make a decision on the purchase.
If you already are a holder of White 414, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime White 414.
However, one of the most important roles played by the user manual is to help in solving problems with White 414. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device White 414 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
