Instruction/ maintenance manual of the product W10282549A Whirlpool
Go to page of 48
INST ALLA TION INSTRUCTIONS UNDERCOUNTER DISHW ASHER INSTRUCTIONS D'INST ALLA TION LA VE-V AISSELLE SOUS PLAN DE TRA V AIL T able of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 T able des matières . . . . . .
T able of Contents W ARNING Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door . Doing so can result in serious injury or cuts.
Drain hose Drain hose clamps (2) (1 large and 1 small) Phillips-head screws (2) Green Silver 2 – under - counter mounting brackets (top) T ools and Parts Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
4 Location Requirements Grounded electrical supply required. Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs. The location where the dishwasher will be installed must provide clearance between motor and flooring.
Product and Cabinet Opening Dimensions 5 NOTE: Shaded areas of cabinet walls show where utility connections may be installed. *Measured from the lowest point on the underside of countertop. May be reduced to 33 ⁷⁄₈ " (86 cm) by removing wheels from dishwasher .
Drain Requirements • A new drain hose is supplied with your dishwasher . If this is not long enough, use a new drain hose with a maximum length of 12' (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.
7 (3.8 cm) Power Supply Cord — Drill hole 1 P r e f r r ed loc a tion Pre f r r ed loc a tion Preferred location Optional loc a tion Optional loc a tion Optional location Drill a 1 ¹⁄₂ " (3.8 cm) hole in cabinet side or rear . See product and cabinet opening dimensions.
6” (15.2 cm) Direct Wire–Route cable 3 Route cable from power supply through cabinet hole (cable must extend to the right front side of cabinet opening). T ape cable to the floor in area shown. This will keep cable from moving when dishwasher is moved into cabinet opening.
9 Flush water supply line 4 Slowly turn water shutoff valve to “ON” position. Flush water into a shallow pan until clear to get rid of particles that could clog the inlet valve. T urn shutoff valve to “OFF” position. Route water supply line 3 Slowly route water supply line through hole in cabinet.
Screw-type clamp Drain trap Large silver drain hose clamp Drain hose Drain trap W aste tee W aste tee No waste disposer – no air gap W aste tee 1. Connect black end of of drain hose to waste tee and cut if needed. (Do not cut ribbed section.) 2. Attach black end of drain hose to waste tee with a large silver drain hose clamp (provided).
11 Air gap Large silver drain hose clamp (provided) Drain trap Air gap Large silver drain hose clamp Drain hose Drain trap Rubber hose connector Screw-type clamps Screw-type clamps Screw-type clamps W aste tee W aste tee No waste disposer – with air gap 1.
What type of electrical connection will you use? Power Supply Cord: Follow Option A instructions Direct Wire: Follow Option B instructions 4 Install a UL Listed/CSA Approved strain relief. Make sure screwheads are facing to the left when tightening conduit nut.
13 WARNING Electrical Shock Hazard Electrically gr ound dishwasher . Connect ground wire to green gr ound connector in terminal bo x. Do not use an extension cor d.
Built-up floors: If the kitchen floor is higher than the cabinet opening's floor - for example, the kitchen floor tile does not extend into the cabinet opening - add shims as needed in the area shown to bring the dishwasher up to 34 " (86.4 cm) below the countertop.
15 Push the plastic buttons out of the side of the tub. NOTE: Save the buttons to cover the holes after dishwasher is installed. Push bracket into slot on the side of dishwasher , and bend tab in toward the side of the dishwasher so that it keeps the bracket in place.
16 Move dishwasher into cabinet opening 7 Insulation blanket screw tensioner spring Closes too quickly— Decrease spring tension 5 When door is unlatched, if door opens by itself, move the tensioner to a higher -numbered hole and replace the screw . Reattach door spring to rear leg.
17 Place paper towel under 90 ° elbow fitting. T urn on water supply and check for leaks. If leak occurs, repeat previous step. If needed, see website for animated representation of this step.
18 Make Direct Wir e Electrical Connection Route cable so that it does not touch dishwasher motor or lower part of dishwasher tub. Pull cable through UL Listed or CSA Approved strain relief in terminal box. Strain relief is not supplied with the dishwasher .
19 T erminal box wire: white blac k ground connector P ower supply wire: white blac k ground wire Wiring configuration If needed, see website for animated representation of this step. Visit www .whirlpool.com/electrical under F AQ tab. T ighten strain relief screws to secure cable.
20 plastic button 6 Check side attachment If securing with a side attachment, check that sides of door do not rub against the screw heads. If they do, dishwasher must be re-centered. When dishwasher is properly centered, replace plastic buttons. Check that top of door does not contact screws, brackets, or countertop.
21 Check that grounding clip is attached to the lower panel. Position the lower panel behind the access panel. On some models there is insulation on the access panel which must fall behind the insulation on the lower panel.
22 First try the solutions suggested here to possibly avoid the cost of a service call. • Has the circuit breaker tripped or the house fuse blown? • Is the door closed tightly and latched? • Has.
Notes 23.
24 T able des matières Risque possible de décès ou de blessure grave si Risque possible de décès ou de blessure grave si vous ne suivez pas les instructions. T ous les messages de sécurité vous dir ont quel est le danger potentiel et vous disent comment réduire le risque de V otr e s é curit é et celle des autres est tr è s importante.
T uyau 2 brides de tuyau d’évacuation (1 grosse et 1 petite) 2 vis Phillips Argenté V ert 2 – brides de montage sous le plan de travail (supérieur) d’évacuation 25 Pince à d é nuder Petit .
26 Exigences d'emplacement Une source d' é lectricit é avec liaison à la terre est n é cessaire. Ne pas placer de canalisation d ’é vacuation, canalisation d ’ eau ou c â blage é lectrique à un endroit o ù cela susciterait interf é rence ou contact avec les pieds ou le moteur du lave- vaisselle.
Dimensions - Produit et cavit é d ’ encastrement 24 " (61 cm)** 34 " (86,4 cm) min* 4 " (10,2 cm) 3 " (7,6 cm) 24 " (61 cm) (4,4 cm) (4,4 cm) (26,7 cm) 2 " (5,1 cm) (6,4 cm) (17,2 cm) D é gag D é gag eme n t D é gageme nt D é gagement (15,9 cm) (1,9 cm)* (62,2 cm) (60,6 cm) 21 " (53,3 cm) (86 cm) min .
28 Exigences d'évacuation • Un tuyau d’évacuation neuf est fourni avec le lave- vaisselle. Si ce tuyau n’est pas suffisamment long, utiliser un tuyau d’évacuation neuf de longueur maxi.
29 1 ¹⁄₂ " (3,8 cm) Cordon d'alimentation é lectrique - Per ç age du trou 1 Empla ce m e nt p r é f é r é Empla c eme n t p r é f é r é Emplacement recommand é A ut r e empla c.
30 6 ” (15,2 cm) Raccordement direct - Acheminement du c â ble 3 Acheminer le c â ble de la source d ’ alimentation é lectrique à travers le trou dans le placard (le c â ble doit d é passer par le c ô t é avant droit de l'ouverture d'encastrement du placard).
Vidange de la canalisation d'alimentation en eau 4 T ourner lentement le robinet d’arrêt jusqu’à la position “ON” (marche). Vider l’eau dans un plat peu profond pour éliminer les particules et débris qui pourraient obstruer l’électrovanne d’admission.
Per ç age du trou 1 (3,8 cm) " Si n é cessaire, percer un trou de 1 ¹⁄₂ " (3,8 cm) de diam è tre dans la paroi du placard ou l ’ arri è re de l ’ ouverture la plus proche de l ’é vier . Installation du tuyau d ’é vacuation IMPORT ANT : Utiliser toujours un tuyau d ’é vacuation neuf.
Dispositif de brise-siphon Grosse bride pour tuyau d' é vacuation argent é e T T T uyau d' é vacuation Siphon Siphon Siphon T Connecteur de tuyau de caoutchouc B Brides à vis R Canalisation d' é gout en T Pas de broyeur à d é chets - avec brise-siphon 1.
34 Risque du poids excessif Utiliser deux personnes ou plus pour déplacer et installer le lave-vaisselle. Le non-respect de cette instruction peut causer une blessure au dos ou d'autre blessure. Risque de basculement Ne pas utiliser le lave-v aisselle jusqu ’à ce qu ’ il soit compl è tement install é .
35 Option A, cordon d ’ alimentation : Acheminer le cordon d ’ alimentation de fa ç on à ce qu ’ il ne touche pas la zone situ é e entre le moteur du lave- vaisselle et la partie inf é rieure de la cuve du lave- vaisselle. T irer le cordon pour l'acheminer à travers le serre-c â ble dans la boucle du bo î tier de connexion.
36 Conducteur du bo î tier de connexion : blanc noir Conducteur de mise à la terre Conducteur d'alimentation é lectrique : blanc noir Fil de mise à la terre Configuration du c â blage Au besoin, visiter le site W eb pour une repr é sentation vid é o de cette é tape.
37 Planchers surélevés (la hauteur du plancher de la cuisine est supérieure à celle de l’ouverture d'encastrement du placard). Par exemple : Le carrelage du plancher de la cuisine n'arrive pas jusque dans l'ouverture du placard.
38 Enfoncer la bride dans la fente sur le c ô t é du lave- vaisselle et replier la languette vers le c ô t é du lave- vaisselle afin de maintenir la bride en place. R é p é ter cette é tape pour l ’ autre c ô t é du lave-vaisselle. REMARQUE : Ne pas fixer le lave-vaisselle.
39 4 Ouverture et fermeture de la porte vis tendeur ressort Se ferme trop rapidement = Réduction de la tension du ressort 5 Pour régler la tension du ressort de la porte, détacher le ressort du pied arrière du lave-vaisselle. À l'aide d'un tourne-écrou ou d'une clé à douille de ⁵⁄₁₆ ", ôter la vis du tendeur .
40 Aligner l ’ avant du panneau de porte du lave-vaisselle avec les portes des placards. Il faudra peut- ê tre ajuster l ’ alignement de celui-ci pour qu ’ il soit en affleurement avec les placards.
41 Placer une serviette de papier sous le raccord coud é de 90 ° . Ouvrir l ’ alimentation en eau et inspecter pour identifier toute fuite. Si une fuite se produit, r é p é ter l ’é tape pr é c é dente. Au besoin, visiter le site W eb pour une repr é sentation vid é o de cette é tape.
42 Former un crochet en U avec le conducteur nu de liaison à la terre. Enrouler le crochet du conducteur de liaison à la terre sur la vis de liaison à la terre et sous la rondelle (dans le sens horaire). Serrer fermement le connecteur de liaison à la terre.
43 Fixation du lave-vaisselle dans l ’ ouverture d'encastrement du placard 1 V é rification de l'alignement du lave- vaisselle dans l'ouverture du placard Ouvrir la porte du lave-vaisselle, ô ter le panier à vaisselle inf é rieur , placer une serviette sur la pompe et le bras d ’ aspersion inf é rieur du lave-vaisselle.
44 Retirer la serviette du lave-vaisselle. Réinstaller le panier à vaisselle inférieur . Suppression de la serviette et r é installation du panier à vaisselle inf é rieur 7 Au besoin, visiter le site W eb pour une repr é sentation vid é o de cette é tape.
45 V é rifier que la rive inf é rieure du panneau inf é rieur est au contact du plancher . Le r é ajuster au besoin. 3 Inspection de la rive de panneau inf é rieure Serrer les vis du panneau d ’ acc è s. 4 Serrage des vis Risque de choc électrique Brancher sur une prise à 3 alvéoles reliée à la terre.
46 Pr é voir des dur é es de lavage plus longues. La dur é e d ’ ex é cution des programmes de votre nouveau lave- vaisselle est d ’ environ 2 à 3 heures par charge, mais il utilise presque 40 % d ’é nergie de moins que des mod è les plus anciens.
.
W10282549A © 2010 Whirlpool Corporation. All rights reserved. Tous droit s réservés. ® Registered T rademark/T M T rad emark of Whirlpoo l, U.S.A., Whirlpool Canad a LP Licensee in Canada ® Marque déposée/TM Marque de commerce de Whirlpool, U.S.
An important point after buying a device Whirlpool W10282549A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Whirlpool W10282549A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Whirlpool W10282549A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Whirlpool W10282549A you will learn all the available features of the product, as well as information on its operation. The information that you get Whirlpool W10282549A will certainly help you make a decision on the purchase.
If you already are a holder of Whirlpool W10282549A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Whirlpool W10282549A.
However, one of the most important roles played by the user manual is to help in solving problems with Whirlpool W10282549A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Whirlpool W10282549A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
