Instruction/ maintenance manual of the product W10038090 Whirlpool
Go to page of 8
W ASHER INSTA LLATION INSTRUCTIONS W A SHER SAFETY W10038 090 T able of Contents WASHER SAFETY ............... .............. ............... 1 INSTALLATION REQUIREMENTS ................ . 2 Tools and Parts ................ .............. ............
2 INST ALLA TION REQUIREMENTS To o l s a n d P a r t s Gather the required tools and parts before startin g installation. The parts supplied ar e in the washer basket.
3 Recessed a rea or closet installatio n The dimensions sh own are for the r ecommended spacing allow ed (A and B), except the closet door ventilation openings. The dimen sio ns sh own fo r th e c loset do or vent ila tion op ening s (C ) are the minimu m required.
4 ■ T o minimize possible shock hazard, the cord must be plugged into a mating, earthing-type outlet, earthed in accord ance with local codes an d ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly earthed outlet installed by a qualified electrician.
5 2. Firmly grasp th e power cord and pull to completely remove the power cord, cor d r estraint, and pin from the rear panel. 3. Confirm that the power c ord r estraint (A), and pin (B) ar e rem o ve d . 4. T o remove the power cor d from the cord r estraint, push the power cord in, press T AB, and then pull the power co rd out.
6 T o keep dra in water from going bac k into the wash er: ■ Do not for ce exce ss drain hose into stan dpipe. Hose should be secur e but loose enough to provide a gap for air . ■ Do not lay ex cess hose on the bottom of the laundr y tub. Floor drain Do not install the drain hose form on to the corrug ated drain hose.
7 5. Attach the cold water hose to the top inle t valve. 6. Screw on couplin g by hand until it is seated on the washer . 7. Using pliers, tighten th e couplings with an additional two-thi rds turn. NOTE: Do not overtighten or use tape or sealants on the valve.
Steps in Final Location 1. Slide the washer to its fin al location. 2. Tilt the washer forward until the rear of th e washer is at least 10.2 cm (4") off the floor . Y ou ma y hear the self-a djusting rear feet click into place. Lower the washer to the floo r .
An important point after buying a device Whirlpool W10038090 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Whirlpool W10038090 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Whirlpool W10038090 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Whirlpool W10038090 you will learn all the available features of the product, as well as information on its operation. The information that you get Whirlpool W10038090 will certainly help you make a decision on the purchase.
If you already are a holder of Whirlpool W10038090, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Whirlpool W10038090.
However, one of the most important roles played by the user manual is to help in solving problems with Whirlpool W10038090. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Whirlpool W10038090 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
