Instruction/ maintenance manual of the product W10038080 Whirlpool
Go to page of 8
W ASHER INSTA LLATION INSTRUCTIONS W A SHER SAFETY W10038 080 T able of Contents WASHER SAFETY ............... .............. ............... 1 INSTALLATION REQUIREMENTS ................ . 2 Tools and Parts ................ .............. ............
2 INST ALLA TION REQUIREMENTS To o l s a n d P a r t s Gather the required tools and parts before startin g installation. The parts supplied ar e in the washer basket.
3 Recessed a rea or closet installatio n The dimensions sh own are for the r ecommended spacing allow ed (A and B), except the closet door ventilation openings. The dimen sio ns sh own fo r th e c loset do or vent ila tion op ening s (C ) are the minimu m required.
4 ■ T o minimize possible shock hazard, the cord must be plugged into a mating, earthing-type outlet, earthed in accord ance with local codes an d ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly earthed outlet installed by a qualified electrician.
5 2. Firmly grasp th e power cord and pull to completely remove the power cord, cor d r estraint, and pin from the rear panel. 3. Confirm that the power c ord r estraint (A), and pin (B) ar e rem o ve d . 4. T o remove the power cor d from the cord r estraint, push the power cord in, press T AB, and then pull the power co rd out.
6 Laundry tub drai n or stan dpipe dr ain Connecting the dr ain hose form to the corrugated drain hose 1. Feed end of drain hose into one end of for m. Place end of drain hose fo rm into the drain h ose relief. 2. Bend the ho se ove r the top of the form a nd feed into t he other end of the form.
7 2. Attaching the hot water coupling first makes it easier to tighten connectio n with pli ers. 3. Screw on couplin g by hand until it is seated on the washer . 4. Using pliers, tighten th e couplings with an additional two-thi rds turn. NOTE: Do not overtighten or use tape or sealants on the valve.
3. Screw the feet into the threaded holes at the front corner of the washer until the nuts touch the washer . T wist the feet to install. NOTE: Do no t tighten t he nuts until the washer is level. 4. Tilt the washer back and remove the wo od block. Gently lower the washer to the floor .
An important point after buying a device Whirlpool W10038080 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Whirlpool W10038080 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Whirlpool W10038080 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Whirlpool W10038080 you will learn all the available features of the product, as well as information on its operation. The information that you get Whirlpool W10038080 will certainly help you make a decision on the purchase.
If you already are a holder of Whirlpool W10038080, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Whirlpool W10038080.
However, one of the most important roles played by the user manual is to help in solving problems with Whirlpool W10038080. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Whirlpool W10038080 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
